Indesit washing machine takes a long time to wash

It can be annoying and inconvenient when your Indesit washing machine takes longer than usual to finish a cycle. Something that used to be as simple as doing the laundry feels like it takes forever. There are several reasons why this problem could arise; some are simple to resolve at home, while others might call for expert assistance.

The first step in fixing the issue is realizing why this is occurring. It might have something to do with a broken part, or it could be as easy as a jammed drum or clogged filters. Taking the time to identify and resolve the problem, regardless of its cause, can prevent more serious issues later on.

The most frequent causes of an Indesit washing machine taking longer than usual to wash will be looked at in this article. We’ll also offer helpful advice on how to diagnose and resolve these problems so you can resume having a more productive laundry schedule.

A malfunctioning heating element, low water pressure, or overloading could be the cause of your Indesit washing machine’s longer-than-usual cycle completion time. These elements may make the machine work harder, which would lengthen the washing time. Your machine can return to its typical cycle duration by comprehending and resolving these possible issues.

What happened to the machine?

Because of how nebulous this "symptomology" is, it is impossible to pinpoint one specific cause of the breakdown right away. But, after doing a situation analysis, you can focus on a smaller subset of potential issues with the equipment’s functionality. Extended washing machine operation may result from:

  • overloading the drum. It would seem, what does the maximum permissible weight of laundry have to do with it? The fact is that the washing machine spends more time distributing the laundry over the surface of the drum, as a result of which the cycle is lengthened. The solution to the problem is very simple – take out the extra things;
  • a problem with filling the tank with water. The duration of the wash can increase significantly if the machine takes a long time to fill with water. This may be due to a clogged filter or inlet hose, a defective inlet valve. Perhaps the valve that shuts off the water is not fully open;
  • a long drain. Several minutes are allocated to remove the waste liquid from the tank. When starting a standard cycle, water is drained from the system at least 3-4 times. Therefore, if you "add" another 5-10 minutes to each drain, the program execution time will increase significantly. Water may have difficulty leaving the drum due to a clogged drain hose, garbage filter, pump;
  • a malfunction of the heating element or temperature sensor. In this case, the water warms up to the desired temperature much longer, as a result of which the program execution time increases. It is possible that a lot of scale has accumulated on the heating element, which has reduced its performance. The problem may also be a faulty thermistor that incorrectly records the liquid heating temperature;
  • damage to the main control unit. The main "symptom" of such a breakdown is that the machine begins to "freeze" during the washing process, after which it starts the cycle again.

The list is actually pretty amazing. In order to resolve the issue, you must perform diagnostics, rule out a number of potential causes, and ultimately identify the type of system failure that took place.

Poor liquid collection, a lot of laundry

It will be more difficult for the machine to handle the distribution of items inside the drum if you load more laundry into it than what the manufacturer recommends. Furthermore, the washing machine will struggle to reach the necessary rotational speed. The cycle will begin in the washing machine, but the washing will proceed more slowly. The laundry will take longer for Indesit to spread out and form lumps on the surface.

It’s crucial to stay within the allowable load weight limit and evenly distribute the items you put inside the drum across the surface.

Regarding the liquid filling slowly, there are a few possible causes:

  • weak pressure in the house communications. If the water in the water pipe barely flows, you should postpone washing until the problem is fixed;
  • not fully open shut-off valve;
  • clogged filter mesh on the inlet valve. In this situation, you will have to clean the filter or replace it;
  • faulty inlet valve. It is necessary to install a new element.

First things first, the most obvious causes of a breakdown must be ruled out. If the program still doesn’t shut off after the wash should have ended long ago based on your calculations, you can check the system pressure, the shut-off valve’s position, and the condition of the inlet hose. You must "dig" a little further if none of the aforementioned factors are the source of the issue.

Slows down on the drain, continuous water intake

If the water in the tank drains too slowly, programs might take longer to complete. A few drainage system components will need to be checked. The following could result in a liquid’s drainage being obstructed:

  • clogged debris filter. The element is located in the front of the washing machine, in the lower right corner. It is necessary to clean the part;
  • damaged impeller. Check if its blades are spinning. This can be done through the hole formed after removing the debris filter;
  • clogged drain pump pipe. To correct the situation, it is necessary to de-energize the washing machine, shut off the water supply, lay the machine on its side, find the pump, loosen the clamp fixing the hose and clean the pipe;
  • dirt accumulation in the drain hose or its kinking. If defects are detected, flush or replace the pipe.

The length of time spent washing is also increased by uncontrollably emptying the tank of water. It is possible to gather water in the system and quickly release it into the sewer. This occurs as a result of:

  • incorrect connection of the washing machine. Water is collected to a certain point and then drained. Thus, the required volume of water does not enter the tank, and washing does not start. Check that the drain hose is installed at a height of 60 cm from the floor. It is important to monitor the position of the hose relative to the washing machine;
  • failure of the pressure switch. The sensor, measuring the water level in the system, sends a signal to the control module about the possibility of starting washing when a sufficient amount of liquid is collected. If the pressure switch is faulty, the level is assessed incorrectly, the washing machine does not understand whether the tank is empty or full. Therefore, water can constantly drain into the sewer and collect again. Replacing the sensor will help to eliminate the problem;
  • inlet valve failures. In this case, the element does not work normally, and may not open completely or completely “freeze”. The problem can be eliminated by replacing the part.

Therefore, when there is an uncontrollable water discharge into the sewer or a clogged drain system, the cycle time increases. You are capable of handling this on your own. It suffices to examine, clean, or swap out the specified Indesit washing machine components for new ones.

Heating problems

Let’s examine what happens when the water is not heated properly, causing the cycle to extend. The heating element or the temperature sensor could be the source of the issue. In this instance, the machine either freezes before it can begin to wash, or it does not turn off and continues to operate far longer than anticipated. The following are the primary causes:

  • a significant layer of scale on the heating element. The quality of tap water often leaves much to be desired, so it is difficult to avoid the accumulation of plaque on various parts of the washing machine. Over time, scale forms on the surface of the heating element. This affects the operation of the element – the water heats up much more slowly. You can try to clean the part or immediately replace it with a new one;
  • malfunction of the temperature sensor. In this case, the signal is not transmitted to the control module that the water warmed up to the desired degree. Then the washing either does not start at all, or is delayed, because the “brain” of the washing machine decides to wait for heating to the set temperature. The machine can “wash” for several hours, waiting until the desired mark is reached. It is enough to replace the thermostat with a working one.

The washing machine will freeze while heating the water, without even beginning to spin the drum, in the event that the heating element burns out.

Usually, the machine alerts the user to the malfunction by displaying an error code on the display if the heating element is totally damaged. Installing a new heating element is the only option in this scenario. Use a multimeter to inspect the old heater before replacing it.

Possible Reason What to Do
Too much detergent Use less detergent next time
Water pressure is low Check the water supply
Machine is overloaded Reduce the load size
Filter is clogged Clean the filter regularly
Settings are incorrect Double-check the selected program

It may indicate an underlying problem if your Indesit washing machine is taking longer than usual to finish a cycle. Frequently, the reason is something as easy as overloading the washing machine or selecting the incorrect wash settings. It might also point to an issue with the machine’s sensors, the heating element, or the water supply.

These delays can be avoided by giving your washing machine regular maintenance and using it carefully. Simple actions like not overfilling the drum, cleaning the filter, and checking the water pressure can have a significant impact.

It might be time to seek professional advice if the issue still doesn’t go away despite your best efforts. Early intervention can save more serious damage and maintain the functionality of your machine.

Video on the topic

Ariston washing machine jumps time, washes endlessly.

Resetting the Indesit WISL102 program

Quick wash 30 minutes, 30 degrees in the Indesit washing machine.

How often do you conduct maintenance of your washing machine (cleaning filters, drum, and t.d.)?
Share to friends
Alexey Volkov

Specialist in service and repair of washing machines. My work has taught me to understand all the intricacies of the device of this equipment. On this site I share my knowledge about how to properly care for a washing machine to extend its service life, and what to do if problems arise. My goal is to help you avoid common mistakes and save money on repairs.

Rate author
FAQ-Washer.com
Add a comment