How to remove the drum from an Electrolux washing machine?

Even though removing the drum from an Electrolux washing machine might seem difficult, you can do it at home if you have the correct instructions. Knowing the procedure can save you time and money, whether you’re doing maintenance or dealing with a broken drum.

It’s critical to gather the required equipment and make sure you are safe before beginning. It is necessary to pay close attention to detail when working with appliances, and it will be much easier if you know the steps ahead of time.

To get your washing machine back in working order, this guide will walk you through every step, from disconnecting the machine to safely removing the drum.

It may seem difficult to remove the drum from an Electrolux washing machine, but with the correct equipment and a methodical approach, you can accomplish it safely and successfully, giving you the opportunity to troubleshoot or replace any damaged parts.

Collect everything you need for repairs

To dismantle the automated machine "without incidents," you must meticulously arrange the necessary supplies. You should start by taking care of the office. The washing machine needs to be moved to a room that is at least 4-5 square meters in size. It’s critical that the space has adequate ventilation and lighting. Because the work will be "wet" and not totally "clean," make sure to cover the floors with rags or, better yet, film.

Apart from setting up the workspace, you ought to:

• study the instructions for the washing machine. Pay special attention to the wiring diagram;
• prepare the tools and devices that will be needed in the process;
• remember the safety rules. It is important to follow them when working with electrical appliances.

Make sure you read the instructions provided by the manufacturer and any other documents included with the equipment before disassembling the washing machine.

You’ll need the following instruments and supplies to remove the washing machine’s drum:

• a pair of screwdrivers: Phillips and slotted;
• a screwdriver;
• a set of wrenches;
• a small hammer;
• an 8 mm Allen key;
• pliers;
• WD-40 aerosol lubricant;
• silicone sealant;
• a ​​hacksaw for metal;
• a marker;
• a low basin and a dry rag (to drain the remaining water from the machine).

Additionally, professionals advise documenting the "home" repair process with pictures or even a video that shows each step of the disassembly process. Reassembling the washing machine and connecting the sensors, pipes, and valves will be simpler as a result. Pay close attention to the wiring; it’s crucial to reattach everything to the designated terminals and connectors.

What will prevent the removal of the tank?

If one adheres closely to the instructions, even someone who has never looked "inside" a washing machine will be able to remove the "tank-drum" unit. The pressure switch, dispenser, heating element, engine, counterweights, and other parts that come into contact with the tank must all be removed first.

Knowing the proper order for disconnecting the components from the tank is essential for a seamless and speedy disassembly. Algorithm for actions.

1. De-energize the washing machine.
2. Turn off the water supply tap.
3. Unscrew the bolts holding the "top" of the case. Remove the cover and put it aside.
4. Unhook the control panel. The "dashboard" is held on by several fasteners, they will have to be loosened. The first pair of clamps "hide" behind the powder receptacle, the rest – along the perimeter of the module. It is not necessary to disconnect all the wiring connecting the panel and the electronic unit. You can simply carefully place it on top of the case, or even better – hang it on the side on a special hook.
5. Drain the remaining water from the machine. There is a special hatch at the bottom of the front panel, in the right corner. Pry it off with a flat screwdriver and open the door. Place a basin under the case, cover the floor around with rags. Unscrew the plug of the garbage filter and collect the water that flows from the hole.
6. Remove the front panel of the case. First, loosen the clamp holding the door cuff, pull it out. Then tuck the sealing rubber inside the drum. After that, unscrew the bolts located along the perimeter of the wall, and pull it towards you. When the "end" moves forward a couple of centimeters, disconnect the wires from the hatch locking device, remove the lock. Behind it, you can completely unhook the front part of the case.
7. Dismantle the main elements connected to the tank: heating element, drain pump, pressure switch, electromagnetic valve, etc.

Verify that the pipe that connects the dispenser to the tank is cut off.

1. Remove the counterweights. Each Electrolux washing machine has two concrete blocks under the lid. The weights give the case stability, "dampen" the vibrations that occur during washing. To remove them, you should unscrew the fixing bolts and slightly shake the "stones". Keep in mind that the elements are very heavy, do not drop the concrete by surprise.
2. Remove the shock absorbers. The springs are the last thing that will interfere with the removal of the drum. Unscrew the posts holding the tank and remove the shock absorbers.

Since the tank holding the "hidden" drum is heavy, it is preferable to remove the entire unit at once. You must grasp the container’s edges in order to pull and raise it.

The crosspiece should be facing up when the disassembled tank is set on the ground or a table. You must unplug the motor from the plastic container after removal. Remove the engine by unscrewing the fixing bolt and set it aside.

Experts advise making the most of the circumstance and making sure that all removed parts are operational right away. Use a multimeter to ring the engine, drain pump, water level sensor, and heating element. Additionally, it is preferable to clean the machine’s "insides" right away. Use soapy water to clean the waste filter, pipes, powder container, and heating element to get rid of limescale.

Although removing the drum from an Electrolux washing machine can be difficult, it is completely possible to accomplish with the correct tools and cautious procedures. To access and safely remove the drum, this process requires disconnecting a number of parts, including the motor, hoses, and control panel.

It’s critical to adhere to the manufacturer’s instructions and take safety measures to prevent harm to the equipment or personal injury. The best course of action may be to consult a professional if you’re unsure about any particular step.

You can successfully remove the washing machine’s drum and take care of any internal problems by following the instructions carefully and understanding the process. This will guarantee that the machine keeps working smoothly.

Video on the topic

Electrolux tank repair, How to replace flanges

How to replace bearings on an Electrolux, Zanussi washing machine!

How to remove the tank of an Electrolux\Zanussi washing machine. Video #33

Replacing bearings in an Electrolux, Zanussi, AEG washing machine

Electrolux. Electrolux, replacing bearings. Washing machine review

Electrolux. Electrolux replacing bearings. Washing machine review.