How to dismantle a washing machine

Are you prepared to take on the chore of taking apart your washing machine? It may seem intimidating to disassemble an appliance, but it’s necessary if you want to move it, fix it, or clean out some difficult parts. But it can be simple if you take the proper approach. We’ll take you step-by-step through the procedure and break it down into digestible portions in this guide.

First and foremost, security is essential. Make sure the water supply is off and the machine is unplugged before beginning. We’ll go over how to disconnect the hoses and safely empty the water. This will assist you in avoiding any possible dangers or mess.

We’ll then go over the various parts of your washing machine and how to get to them. Knowing how each component fits together, from the drum to the top panel, will make disassembly much simpler. We’ll provide you helpful hints and detailed instructions so you can handle each piece with care.

These instructions will provide you the tools you need to confidently handle the disassembly process. Whether you’re a do-it-yourself enthusiast or just want to learn more about your machine, this guide will help you get the job done quickly and effectively.

Knowing the proper procedures can make disassembling a washing machine much easier if you’re up for the challenge. This tutorial will walk you through the best way to disassemble your washing machine safely and successfully, covering everything from unplugging and emptying to taking out each part. By adhering to these simple instructions, you’ll be ready to explore your machine’s internal operations with assurance and little difficulty.

Preliminary actions

The first step in disassembling the washing machine is to get ready to cut off communications. Firstly, we are discussing the power supply—that is, if you can reach the socket and plug without having to tilt the case. Naturally, the machine that is being disconnected shouldn’t be in the middle of washing, and it should ideally dry thoroughly after the final cycle. We then take the following actions.

1. We turn off the water supply valve on the water supply (as a rule, it is located on the pipes behind the washing machine or under the sink). Turn it clockwise until it stops. Most often, only cold water is supplied to the machine, if there is hot water, we repeat the procedure with the second valve.
2. Move the unit away from the wall, alternately moving each edge forward. If a built-in model is installed or the machine is too heavy and clumsy, involve an extra pair of hands.
3. Calculate such a distance from the wall so that the connected hoses are not in a taut state, and there is enough space for free access to the back wall.

The machine is now prepared for disassembly. All that’s needed is a flat screwdriver, round-nose pliers, tape, and a few rags and containers to catch water. We will discuss disconnecting the hoses in more detail later, but all of this will be useful.

Preservation of the machine

It is important to realize that water is always present inside the washing machine, and that liquid can easily get on the wiring or electronic board if the machine is not emptied before tilting or jumping during transportation. It is best to "preserve" the machine with care because the effects of excessive moisture are depressing. To accomplish this, take these actions:

• place the prepared containers behind the machine under the waterline, and spread the prepared rags around, be prepared for the fact that water will spill and splash;
• check whether the water supply valves are closed, it is worth considering that it is easy to accidentally turn the switches to the open position;
• wait about a minute after closing the valves so that the pressure in the hoses returns to normal;
• remove the clamps on the inlet hose on both sides, lower it into a bucket or basin and drain the water.

The hoses must be rotated clockwise to be unscrewed; if this proves challenging, use pliers, a flat screwdriver, or a wrench. It is only possible to remove plastic nuts by hand.

Be careful! When using tools, use moderate pressure because too much force can easily strip the thread and break the nut.

With the drain hose, repeat the process. Depending on the current drain, there are multiple variations in this case. This could be a sewer built into the wall, a hole in the floor, a connection to a sink siphon, or a shared water supply. The most important steps are to flip the switch, shut off the water, remove the hose, loosen the clamp (if any), and remove the rubber gasket. You can wait for the machine to dry out on its own. Pour the drained water in during this time, and then dry wipe the floor. to prevent slipping when the washing machine is being further prepared for relocation.

Preparing a machine for transportation

In the last step, we circum circumambulate the washing machine from all angles to make sure all wires and hoses are disconnected. It is strongly advised that you set aside some time to thoroughly clean the pipes at the location where the drain is disconnected. To do this, we will take a brush and meticulously remove all of the debris that has accumulated during operation. We inspect the drain filter, wipe the dry receiver, and look inside the drum. Additionally, remember this:

• Remove the power cord or place it in specially provided grooves, and for reliability – fix it with tape (then you will not have to be afraid of accidental disconnection or damage to the plug);
• unscrew the handles from the body of the washing machine;
• close and seal the door and powder receptacle with tape;
• To fix the drum by putting a V-shaped piece of foam rubber into the tank, stuffing it with linen, using special bolts or tightening the screws provided on the rear wall of the case.

Crucial! It is best to read the typewriter’s user manual and determine which approach works best for the model that is available.

Wrapping all components, hoses, handles, and cords in paper or rags completes the preparation. Packing the washing machine into a foam frame from the store and covering it with cardboard or cloth would be a smart idea. Moving the machine to the intended location without causing it to tilt, shake, or jump is all that’s left to do.

Although disassembling a washing machine may appear difficult, it is manageable with a little perseverance and the appropriate technique. Make sure you have all the required equipment and safety gear first. It is essential to unplug the machine from water and power sources in order to avoid mishaps. You can avoid future headaches by carefully following each step and taking your time.

Make sure you record the number of screws and parts you remove. Assembling these components in order will facilitate reassembly considerably. Taking pictures of each step is also beneficial so you have a record to refer to in case you need it. Do not hesitate to refer to the machine’s manual or get professional assistance if you run into any problems.

Keep in mind that replacing or troubleshooting parts is frequently the purpose of disassembly, so handle each part with caution. After the task is finished, make sure everything is put back together correctly and give the machine a test run to make sure it’s operating as it should. It should be much less scary to take on a washing machine disassembly project if you keep these suggestions in mind.

Video on the topic

Disassembled the washing machine to the giblets.What useful things can be taken from the parts

How to install a new washing machine in place of the old one?

How to move a washing machine alone

How to turn off the washing machine and prepare it for transportation – filmed on video

How to disconnect the washing machine from the water supply