Getting clean clothes with every load depends on keeping your washing machine in good operating order. A noisy or jerky spinning drum is a frequent problem that can occur and is typically brought on by a worn-out or dry bearing. Understanding how to properly lubricate the bearing in your Indesit washing machine can prolong its life and maintain smooth operation.
You can avoid expensive repairs or replacements by following this step-by-step guide, which will take you through the entire process. With the correct tools and a little perseverance, you can do this task yourself regardless of your level of experience with appliance maintenance.
Not only can you save money by learning how to properly lubricate the bearing, but you’ll also extend the life and functionality of your Indesit washing machine.
- Choosing the right material
- Getting to the bearings
- Video on the topic
- Replacing bearings in an Indesit washing machine, the most important
- Myself. Repairing a washing machine motor. Bearings are noisy.
- How to quickly cut a glued tank of a washing machine. Indesit – Russia, how to change bearings
- Indesit washing machine. Replacing bearings 202/203. No comments.
- Replacing a bearing in an Indesit washing machine
- Indesit washing machine. Checking bearings
Choosing the right material
Selecting a detergent for the washing machine is the first step. This product comes in a wide range of varieties, each with unique characteristics, all available on the market. Let’s determine which type of grease is best for seals and bearings.
- Moisture-resistant. Due to the fact that the seal located on the bearing and protecting the part from moisture is constantly in contact with liquid, the grease must be resistant to water. If it does not remain on the sealing ring after contact with water, then such a product is not suitable for processing the unit.
- Heat-resistant. This is also extremely important, because the grease must withstand both the high temperature of hot water and the heating of the shaft during extremely fast rotation of the drum, for example, during spinning. If the product does not withstand heating and loses its properties, then it will let moisture into the bearing.
- Suitable for rubber, non-aggressive. A high-quality product will not deform during operation and will not cease to be hermetic.
- Thick. Finally, the last point is relevant due to the fact that the product should not leak out while the washing machine is running.
Automotive products like "Litol-24" or "Azmol" should not be used because they lack the necessary qualities and may cause the SM’s bearing unit to fail.
It is very simple to locate high-quality household appliance products. The following goods are typically used by service centers:
- AMPLIFON. High-quality Italian product from the MERLONI brand;
- Anderoll. Lubricant recommended by the manufacturer. It can be found in syringes, as well as in cans designed for 100 grams;
- STABURAGS NBU 12. Also a good moisture-heat-resistant option for the Indesit washing machine;
- LIQUI MOLY "Silicon-Fett". High-quality silicone grease, made in Germany, sold in 500 gram tubes;
- Huskey Lube-O-Seal PTFE Grease. Another effective water-resistant product that can be used to treat seals with bearings.
Investing in high-quality lubricant to protect the "home assistant’s" internal components is preferable to cutting corners on repairs.
Getting to the bearings
You can move on to the next step if the treatment agent has been chosen. You will need to disassemble the machine nearly entirely in order to get it back to working normally, so it is best to call a specialist if you are unsure of your ability. If you’re prepared to fix it on your own, then adhere closely to our recommendations.
- First, disconnect the household appliance from all communications.
- Move the device to the center of the room to get free access to all sides of the case.
- Disconnect the top panel by removing the two fixing bolts at the back.
- Remove the drawer for household chemicals.
- Remove the control panel, having previously disconnected the wiring.
It is best to take pictures of the wire connections to the board just in case, so you have a visual reference when reassembly is necessary.
- Carefully disconnect the rubber seal by bending the fixing spring and removing the retaining clamp. Tuck the edges of the cuff into the drum.
- Remove the bottom panel of the case, secured with latches.
- Tighten the bolts that hold the front wall of the CM. Most often, they can be found behind the detergent drawer, as well as under the bottom and top panels.
- Remove the front panel of the machine, having previously disconnected the wiring from the control unit to the UBL.
- Disconnect the pipes from the tank, the wiring from the water heater, pump, electric motor and sensors.
- Unhook the pressure switch from the side wall along with the wiring and tube.
- Remove the counterweights from the case.
- Make sure that you have disconnected all the wires with pipes from the tank.
- Remove the drive belt.
- Unscrew the shock absorbers, and then remove and lay the tank with the pulley up.
- Unscrew the corresponding screws and dismantle the electric motor of the machine.
It’s evident that disassembling an Indesit washing machine is a time-consuming and tedious task, so estimate how many hours the repair will take.
| Step | Instructions |
| 1 | Unplug the washing machine and disconnect water supply. |
| 2 | Remove the back panel to access the drum. |
| 3 | Detach the belt and pulley from the drum shaft. |
| 4 | Carefully take out the bearing using a bearing puller. |
| 5 | Clean the bearing and surrounding area. |
| 6 | Apply high-quality grease to the bearing evenly. |
| 7 | Reassemble all parts in reverse order. |
| 8 | Test the machine to ensure smooth operation. |
Maintaining your Indesit washing machine on a regular basis can help keep major problems at bay and increase its longevity. One of the key maintenance procedures that guarantees the machine operates silently and smoothly is lubricating the bearings.
Make sure you have the necessary equipment and a bearing-specific lubricant before you begin. By taking the time to carefully apply lubricant and gain proper access to the bearings, you can prolong the life of your machine and minimize wear and tear.
You can keep your washing machine operating properly and save money on repairs by following these instructions. This kind of routine maintenance greatly improves the longevity and functionality of your appliance.
An Indesit washing machine’s bearing must first be accessed by disassembling components like the drum and seals, after which any dirt or old grease must be cleaned out. By extending the machine’s lifespan, preventing wear, and reducing noise, applying premium, water-resistant bearing grease ensures smooth operation and helps save money on future repairs.
