Although removing a bearing from a Samsung washing machine drum may seem difficult, it is something you can do on your own if you have the necessary equipment and a little perseverance. Bearing wear and tear over time may result in noisy operation or even damage to the drum. By learning how to replace them yourself, you can prolong the life of your appliance and avoid paying a professional’s fees.
Prior to starting, it’s critical to comprehend the fundamental procedures and assemble the required equipment. This task necessitates disassembling your washing machine to some extent, so be sure you’re comfortable disassembling and reassembling appliances. Prioritizing safety above all else means that you should always unplug the machine before using it.
We’ll take you step-by-step through the procedure in this guide, making sure you have all the knowledge required to remove the bearing from your Samsung washing machine drum successfully. This guide will assist you in completing preventive maintenance, whether you’re dealing with a noisy spin cycle or simply want to get the job done.
With simple tools and a little perseverance, you can easily remove a bearing from the drum of a Samsung washing machine and repair your machine on your own, saving you money on professional assistance.
- We try to carefully knock it out
- You need to remove the stuck races and their parts
- Video on the topic
- How to replace bearings in a Samsung washing machine. Replacing the crosspiece. Disassembly from A to Z.
- Replacing bearings on a SAMSUNG washing machine Playlist "Washing machine repair in Sochi!".
- REPLACEMENT OF SAMSUNG WASHING MACHINE BEARINGS!
- 📢Replacing Atlant washing machine bearings How to replace washing machine bearings👍🛠️❗
We try to carefully knock it out
It is not too difficult to remove the bearings from a Samsung automatic washing machine in normal circumstances. A standard punch and hammer can be used to remove the rings if they are undamaged and not adhered to the shaft. This is what you must do:
- place the chisel on the outer rim of the bearing;
- constantly moving the punch along the diameter of the ring, tap the part.
The multipurpose lubricant WD-40 will make it easier to remove a jammed bearing.
Use WD-40 aerosol to spray the bearing if a chisel and hammer are unable to remove the element. After that, you must wait 15 to 20 minutes for the medication to start working. Once more, attempt to disassemble the ring.
In the same way, the washing machine’s inner bearing gets destroyed. The only distinction is that the inner race of the ring must be struck with the punch. The blows from the hammer shouldn’t be very forceful.
Knocking out usually eliminates both bearings completely. Rarely, a portion of the bearing cage may become lodged on the shaft or within the drum. Although it is hard to remove, it is essential. We’ll walk you through extracting a partially destroyed element.
You need to remove the stuck races and their parts
It is preferable to avoid leaving a portion of the bearing in the washing machine’s drum. You will need to stock up on extra time and tools if this occurs. In any case, you have to remove the race; otherwise, you can’t fix the automatic machine.
You will need the following to free the stuck bearing race:
- hammer;
- thin metal drift (1.2-1.5 cm in diameter);
- slotted screwdriver;
- grinder;
- gas wrench.
The following will be the sequence of events:
- clean the seat;
- treat the "nest" and the remaining part of the bearing with WD-40 lubricant;
- wait 15 minutes for the liquid to take effect;
- Use a screwdriver to clean off all rust, wear and loose dirt from the clip;
- Treat the unit with WD-40 liquid again;
- Wait another 10 minutes;
- turn the drum lid over and inspect the seat from the back side – the edge of the stuck bearing cage will stick out there;
- Put the pitch so that it rests on the protruding edge of the stuck ring;
- Moving the pierce cross, tap the internal support.
At most, a few hammer blows will cause the clip to come loose. You will need to tap the rim twenty times on average. If you are unable to obtain a destroyed element, run WD-40 aerosol grease through the node once more. After the support has "smeared," wait ten to fifteen minutes and proceed to knock out the part.
There are instances when the clutch is on the drum shaft rather than in the landing "nest." In this instance, it’s essential to:
- Process a WD-40 with a liquid closed liquid;
- wait 15 minutes until the part “smears”;
- twist a clip with a gas key.
You will need to use heavy artillery if the key slides. Now, take the grinder:
- use a grinding machine to make notches on the stuck collar on the right and left (this must be done carefully so as not to damage the shaft sleeve);
- treat the area with WD-40 aerosol again, wait 15 minutes.;
- remove the rim with a gas wrench (the marks made by the grinder will help with this).
It is a mandatory safety rule to wear special protective glasses when using a grinder.
You will be able to press out the broken bearing in any event. The only drawback is that, depending on circumstance, the task may take anywhere from twenty minutes to several hours. It’s critical to accumulate spare time and patience. You must proceed with extreme caution to avoid damaging the drum shaft or the tank.
The seat just needs to be cleaned of any remaining dirt, rust, wear indicators, and metal shavings. After that, you can install the new parts, which include the oil seal and the bearings. The same hammer and punch are used to press the rings in. The washing machine’s tank and internal components are put together in the opposite order.
| Step | Instructions |
| 1 | Disconnect the washing machine from power and water supply. |
| 2 | Remove the top and back panels to access the drum. |
| 3 | Take off the drive belt and pulley from the back of the drum. |
| 4 | Detach the drum by loosening the bolts that hold it in place. |
| 5 | Carefully pull out the drum to expose the bearings. |
| 6 | Use a bearing puller to remove the old bearings from the drum. |
Maintaining the performance of a Samsung washing machine requires the bearing to be removed from the drum with success. You can confidently take on this repair project by carefully following the instructions and using the appropriate tools.
To prevent further damage, always take your time and handle each component of the washing machine carefully. It’s wise to refer to the handbook or get expert assistance if you have any questions at all.
You can avoid costly repairs and prolong the life of your washing machine by exercising patience and close attention to detail.
