Handling an error in your washing machine can be quite annoying, particularly if it’s something like Error E08 on a Candy model. Knowing what this particular error code means will help you handle it more skillfully as it’s a common problem that many users encounter. Error E08 usually denotes a malfunction with your machine’s water supply or water level sensor.
It’s helpful to first see if the hose is kinked or blocked, or if there’s a problem with the water inlet, in order to fix this problem. Sometimes the issue can be resolved with a quick fix, like clearing the filter or making sure the water supply is on. Should these measures prove ineffective, the problem may be more intricate and necessitate expert assistance.
We’ll go more deeply into the typical causes of Error E08 in this post and walk you through the troubleshooting and solution steps. Our aim is to assist you in resolving any issues and getting your Candy washing machine back up and running as quickly as possible.
| Error E08 | This code usually indicates a problem with the water temperature sensor in Candy washing machines. |
| Possible Causes | Issues could include a faulty sensor, wiring problems, or a defective control board. |
| Steps to Fix | Check the sensor connections and wiring. If they seem okay, you might need to replace the sensor or call a technician for further inspection. |
| Preventive Tips | Regularly clean the washing machine and check for any loose connections to avoid similar issues. |
Checking the tachogenerator and engine
Regretfully, a thorough explanation of the E08 error is absent from the instructions that are attached. It just states that it happens when the motor tachogenerator malfunctions or short circuits. It also happens less frequently when the control module malfunctions and can also happen when the engine fails. First, you should determine whether the following components can be operated based on the information provided:
- motor;
- tachogenerator;
- control module.
The verification demands adherence to a specific algorithm. After removing the motor with the tachogenerator at the first stage, the following actions are taken:
- disconnecting the machine from the power supply;
- removing the screws from the rear panel;
- dismantling the panel itself;
- removing the drive belt while simultaneously pulling it towards you and turning the pulley.
The engine should then be removed. To avoid problems during the connecting process, it is advised that you mark the wires originating from the motor before beginning. Next, take the engine out of the housing by unscrewing the bolts holding it in place. We now examine the machine’s Hall sensor, which may become loose due to excessive vibrations that could cause the fastening or contacts to loosen. All that’s required in such a case is to tighten the fastening bolts and make the connections again.
If this wasn’t the issue, you’ll need to examine the tachometer’s resistance. There are two ways to go about this.
- Setting the tester to the resistance detection mode. It is necessary to loosen the wire connectors and remove them from the sensor contacts. Then the probes are attached to the contacts to check the resistance. A normal indicator is the range from 60 to 70 Ohms.
- The tester switching to the voltage determination mode to understand whether the current is being developed or not. To check, the probes are superimposed on the sensor contacts with simultaneous engine scroll. If the values change (approximately 0.2 Volts), then the part is in working condition.
Verifying the integrity of the wiring is essential because it frequently causes the tachogenerator to malfunction. Additionally, the part will need to be fixed or replaced entirely if it is defective.
If the problem hasn’t been found yet, you should check the motor next. We inspect the brushes at the first stage and replace them if necessary because they are worn out.
This part is available for purchase through specialty stores or through the "custom-made" service. You can accomplish this by typing in the necessary request into a search engine and locating the required organization.
Thus, we check for breakdowns in the wiring that supplies the tachometer and the motor using a multimeter. You will need to examine the rotor and stator resistance if no breaks are discovered. Next, we test the interturn short circuit in the winding and see if there is a current leak to the housing. In the event of a breakdown, installing a new motor would be the best course of action because repairing the motor would be very expensive.
When a Candy washing machine displays error E08, there is usually a problem with the door lock mechanism. This can mean that the door isn’t closed all the way or that there is a problem with the locking system. Knowing what this error means will enable you to troubleshoot and fix it quickly, keeping your washing machine in good working order and preventing disruptions to your laundry schedule.
While dealing with Candy washing machine Error E08 can be annoying, once you know what to look for, it’s usually a manageable problem. This error usually indicates that there may be an issue with the heating element in your machine, which could be preventing it from washing or drying your clothes properly.
Try turning the machine off and back on again to reset it first. Should that prove ineffective, you may need to examine the heating element or seek professional assistance for a more comprehensive assessment. Occasionally, a straightforward repair like changing a fuse or cleaning connections will take care of the issue.
In the end, being aware of Error E08 enables you to resolve the problem successfully, sparing you time and possibly expensive repairs. Your washing machine’s lifespan can be increased and its functionality maintained with routine maintenance and prompt repairs.
