The washing machine does not start and indicators do not burn

When you load your washing machine, hit the start button, and nothing happens, it can be quite frustrating. You wonder what’s wrong when the machine won’t start and the indicators don’t illuminate.

There are a number of potential causes for this issue, ranging from straightforward power outages to more intricate internal issues. Gaining insight into the possible causes of this malfunction will assist you in troubleshooting and determining whether a professional solution is required or if a quick fix will suffice.

Let’s look at some typical causes for your washing machine not starting as well as troubleshooting solutions.

What could break?

A laundry room that was operating normally yesterday could stop working at any time. In this case, nothing happens when the machine is plugged in and the network key is pressed; no sound signal is produced, and the control panel’s LEDs stay dead. The following could be the causes of this technological "behavior":

• a malfunction of the outlet where the network wire is connected;
• damage to the cord fork;
• turning off electricity in a house or apartment;
• failure of the interference suppression filter;
• defective power cord;
• sticking or damage to the "On" button.
• malfunction of the control module;
• break in the wiring inside the washing machine.

Therefore, you should identify the likely cause of the malfunction before contacting a technician. It is simple to replace a burned-out cord, its plug, and a damaged power filter by yourself. Fixing the start button is also simple. Now let’s determine where to begin the diagnostics.

Pay attention to electrical communications

One common scenario is when there is no electricity supply and the machine does not turn on. It frequently occurs that after scheduling a wash, the hostess tries to turn on the machine but nothing happens. Click the closest switch to see if there is any light in the apartment. It could be that your panel’s fuses have blown or that there is no power in the entire house.

A malfunctioning rosette is another issue that can cause a malfunction. The contacts might have burned out if it’s old. Checking the power point is simple: just plug in any other electrical device, such as a lamp, kettle, or hair dryer. When small household appliances refuse to operate, the outlet is actually the source of the issue.

If the outlet is operational and there is light in the apartment, what should you do? This indicates that the washing machine is the source of the issue. It is best to carry out the check from simple to complex. Examine the network cable and plug first; if there are any defects or a burning smell, you will need to replace the parts.

The washing machine may not turn on and the indicators may not light up as a result of power spikes in the network.

Voltage surges have the potential to cause damage to the plug or start a fire in the network cable. The multimeter is used to check the cord. A tester is used to ring each wire inside the insulation.

The network filter is the next item on the inspection list. This dampens voltage surges in the network, protecting the electronic microcircuits that are crammed into a modern automatic washing machine and shielding it from various interferences and blows. The washing machine’s main modules lose power when the capacitor burns out, which prevents the device from turning on.

The network filter is something you can inspect and, if needed, change on your own. The following will be the sequence of events:

• de-energize the automatic machine, turn off the tap on the water pipe;
• move the machine away from the wall to have access to the back of the case;
• unscrew the 2 screws holding the top panel of the washing machine;
• put the cover of the machine aside;
• find the interference suppression filter – it is located where the network cable exits the washing machine;
• disconnect the wiring from the capacitor and pull it out of the machine;
• set the multimeter to buzzer mode;
• ring the filter for breakdown;
• if there is no breakdown, check the resistance of the FPS.

The component has burned out and needs to be replaced if the network filter outputs resistance of 0 or 1.

It is best to show the store manager the original, burned part in order to select the correct capacitor. The expert will then provide you with a comprehensive analogue. Inform the seller of the automatic machine’s model and serial number if this is not feasible. Installing a new filter is very simple; just attach it with bolts in the same location and reconnect the wiring that was taken out earlier. After that, the machine is inspected and the case is put together. The washing machine should function after the capacitor is replaced if it was malfunctioning.

There could be a number of reasons why your washing machine won’t start and the indicators don’t light up, including a malfunctioning control board, a faulty door switch, or a power supply issue. You can troubleshoot the problem and decide whether you can fix it yourself or if you need to call in a professional by being aware of these common causes.

The power button does not respond

The machine may occasionally refuse to turn on precisely due to a broken or stuck power button. Frequently, the contacts just oxidize and become unresponsive to pressure. As soon as the power cord and interference filter have been diagnosed, this assumption is verified.

You will need to take off the machine case cover in order to disassemble the button. After the wires are removed from the key, it is advisable to take a picture of the connection diagram as it will be useful for reinstalling the component. After that, you must pry open the latches to remove the button.

First, a multimeter is used to ring the button that was removed. Next, the resistance it generates is examined. Once the malfunction has been located, the part needs to be changed. The experts advise trying this solution because cleaning the contacts can sometimes solve the issue. You will need to replace the key even if it still doesn’t ring after this.

Your washing machine may have a simple problem with a loose power connection or a more complicated internal component problem if it won’t start and the indicators don’t light up. Frequently, the problem can be rapidly fixed by checking the power supply, the fuse, and making sure the door is closed properly.

If these remedies don’t resolve the issue, it may be more serious and call for expert assistance. Problems pertaining to the control panel or wiring are not amenable to DIY solutions and must be addressed by a professional.

Your washing machine will last longer and function more dependably if you give it regular maintenance and operate it carefully.

Video on the topic

Indesit IWUD 4085 washing machine does not turn on, the indicators do not light. What to do?

If the SAMSUNG washing machine does not turn on

LG washing machine does not turn on (another case)

Bosch washing machine does not turn on | Bosch logik8 does not start washing

LG does not start, LG washing machine does not work, the start button does not start washing.