Indesit washing machine does not turn on

It can be very frustrating to have an Indesit washing machine that won’t turn on. This problem can throw a wrench in your plans, whether it arises first thing in the morning or just before you need to change into clean clothes for a big event. You can troubleshoot the issue by checking a few things on your own before calling a repair technician.

First, confirm that the power supply is operational and that the machine is correctly plugged in. Occasionally, a tripped circuit breaker or a loose plug may be the cause. Additionally, look for any obvious damage on the power cord.

Examine the door latch after that. The machine might not start if the door isn’t closed all the way or if the latch isn’t working properly. Make sure the latch mechanism is working properly and the door is closed securely.

It could be worthwhile to investigate the machine’s control panel and settings if these fundamentals are unable to fix the problem. Occasionally, a problem with the electronic controls may make it impossible for the machine to start. You can try unplugging the machine for a few minutes and then plugging it back in to reset it.

Finally, it may be time to seek professional advice if none of these measures resolve the issue. Occasionally, the final fix calls for a technician to examine internal parts that are beyond the scope of simple troubleshooting. With the help of these suggestions, you ought to be able to fix the problem and restart your washing machine.

Probable causes of breakdown

Even a total novice can tell in this case that the Indesit washing machine’s modules are inactive because it has disconnected from the power source for whatever reason. This implies that you must inspect all electrical and electronic components, both inside and outside the washing machine. It is advisable to commence with the most basic and apparent explanations, such as:

• malfunctions in the electrical network, or it is completely de-energized;
• the outlet from which the Indesit washing machine is powered is de-energized or burnt out;
• the plug is burnt out or the wire of the power cord is burnt out.

Now, maybe some of our readers will spit in their mouths and say, "Why can’t I figure out whether there is electricity in the house or not?," or something to that effect. The writers of this article have become utterly impudent. Don’t rush to curse, though; the de-energized electrical network isn’t the only issue. We will talk about local issues in the publication’s next section, but for now, let’s look at some less apparent reasons why things break down.

1. The FPS has been knocked out.
2. The varistor or the on/off button of the washing machine has burned out.
3. An element of the control microcircuit has burned out.

Crucial! If the Indesit washing machine’s symptom was indeed caused by this breakdown, then the control microcircuit would need to almost entirely burn out before the machine completely loses power.

Something with the electrical network

If the washing machine won’t turn on, try not to freak out and think of a million different problems. It’s possible that the electrical network that powers the machine is the source of the issue instead of the machine itself. Experts advise examining the outlet that the machine is connected to first if the Indesit brand "home assistant" is not turning on. It is simple to check if the socket functions by plugging in a functional electrical appliance.

Exercise caution! In order to prevent electric shock or even fire, turn off the socket as soon as you discover a problem and do not connect anything to it.

If the outlet is de-energized for any reason, you should call in a professional electrician to help you figure it out. If you decide to fix your own home electrical network, proceed with caution, make sure you turn it off before doing anything, and make sure you abide by safety precautions.

Network cable or FPS

The washing machine continues to "get on the nerves" of the owner and hostess in every way, even though the socket is fine. It also still does not work and does not turn on. Thus, we examine the plug, the network cable, and the interference filter all at once. The network cable and FPS on the Indesit washing machine must be removed for joint inspection because they are assembled together. How can the Indesit washing machine’s network cable and network capacitor be removed?

• Disconnect the drain hose, inlet hose and power cord from the utilities.
• Turn the washing machine towards you with the back wall.
• Unscrew the screws and remove the top wall (cover).
• Look under the cover. In the upper part of the case in the lower left corner you will see a network capacitor, remove it from the mount.
• At the base of the case there is a special mount that holds the network cable, it also needs to be removed.
• Now all that remains is to pull the FPS out of the machine case along with the cable and plug.

Next, you must examine the network cable and the FPS independently to determine why the Indesit washing machine isn’t turning on. Remove the network cable’s contacts and set the FPS aside; we’ll examine the capacitor later. Using a multimeter, dial the wire as indicated in the figure below after setting the device to the dialing mode. The masters advise against replacing the wire cores individually if the wire does not ring, as this indicates a breakdown and the need to replace the wire.

Before using a multimeter to check anything, make sure the device is in good operating order. To accomplish this, turn on the resistance measurement mode and join the probes of the activated device. On the display of a functional device, zeros or a value very close to zero should be displayed.

Let’s check the FPS now. Since our multimeter is already set to ring, we can check the capacitor contacts right away by placing the probes on them. We reconfigure the device to measure and check the resistance if the capacitor rings. The washing machine won’t turn on if the multimeter reads zero or one, which indicates that the capacitor has burned out.

Varistor or control microcircuit

The Indesit washing machine isn’t turning on or working properly. Perhaps the so-called varistor is the cause of all this. This component of the control microcircuit shields the microcircuit from high voltage in the network with a semiconductor resistor. The Indesit washing machine microcircuit’s varistors frequently burn out when there is a voltage drop in the electrical network, causing the machine to "stop dead" and not turn on.

One of the few components of the control board that you can inspect and replace yourself is the varistor. This is our plan of action.

1. We take out the powder tray, then find two screws under it near the niche, which should be unscrewed.
2. Unscrew the three screws on top (under the cover) holding the control panel.
3. Remove the control panel.
4. Disassemble the unit and remove the control microcircuit.
5. We find the varistors on the board and check the resistance of each part with a multimeter.

A burnt varistor is usually visible right away. Frequently, they burn out or turn black with the tracks.

1. If a burnt varistor is found, take a soldering iron and solder the legs of the faulty part and remove it.
2. We buy a similar part in a specialized outlet and solder it in place of the burnt one. Ration needs to be done very carefully so as not to damage the paths.

After the return assembly, if everything is done correctly, the washing machine will function as intended. It’s possible that the tracks and other semiconductor components on the control board will burn out in addition to the varistor. In this instance, leave the repair to an expert if the washing machine won’t turn on. If you start fixing the management fee on your own, you might eventually damage the pricey microcircuit and have to replace it, which could cost as much as one-fifth of the price of a new washing machine.

The majority of official service centers only replace schemes when they break rather than fixing them. For them, it is therefore more profitable. However, you can find someone who will take up the restoration of this part if you make several calls to private masters.

There are several common problems that could be the cause of your Indesit washing machine not turning on. This post will walk you through a few basic troubleshooting techniques to assist in identifying and possibly resolving the problem on your own. We’ll go over doable fixes to get your washing machine working again without requiring a professional repair, like inspecting the fuse and making sure the door is closed correctly, as well as testing the power supply.

It can be annoying if your Indesit washing machine won’t turn on. Examine the essentials first, such as the power supply and any circuit breakers that may have tripped. Simple problems like a broken power cord or a loose plug can occasionally be the cause. Since many models won’t start if the door isn’t fully locked, make sure it’s closed securely.

Examine the internal parts of the machine next. Keep an eye out for any indications of broken components, such as the control board or fuse. It might be necessary to hire an expert if all of these parts are functional but the machine still won’t turn on. They are able to identify more complicated problems that are difficult to see.

Recall that routine maintenance can aid in the avoidance of these issues. Monitor the functionality of your computer and take care of minor concerns before they become major ones. In the end, maintaining your washing machine will make sure it continues to function well for many years to come.

Video on the topic

The washing machine Indesite does not turn on

Indesit washing machine does not turn on

Windy module repair part 1 Indesit washing machine does not turn on

Indesit washing machine repair | Does not turn on

Indesit washing machine does not turn on. Why the washing machine does not start

Indesit WISN 82 washing machine repair does not turn on Simple repair