It may seem impossible, but you can replace the bearing in an LG washing machine with direct drive on your own if you have the correct instructions. One essential part that keeps the drum spinning smoothly is the bearing. It will begin to make loud noises during the spin cycle when it wears out, and if you ignore it, it may cause more serious damage.
This tutorial will take you step-by-step through the procedure, giving you the assurance you need to finish the job. You can prolong the life of your washing machine and reduce repair expenses by adhering to these instructions.
With the correct tools and some basic know-how, replacing the bearing in an LG washing machine with direct drive is a task that can be completed at home with meticulous attention to detail. To get the machine operating smoothly again, the procedure entails removing the drum, getting to the bearing assembly, and installing the new bearing.
- Tools and components
- Removing the tank-drum unit
- Video on the topic
- LG 8 kg washing machine repair. Direct drive. Video instruction! Replacing drum bearings.
- How to change bearings in an LG washing machine with direct drive.
- LG Direct Drive. direct drive, replacing bearings. Washing machine review.
- Replacing bearings in an LG washing machine
- Replacing bearings in an LG washing machine
- 📢 Replacing bearings in an LG washing machine Full cycle ⏲️How to Replace LG Washing Machine bearings👍
- Replacing bearings in an LG washing machine with direct drive || Washing machine repair in Kaluga
Tools and components
When a malfunction initially appears, it can be challenging to determine that worn-out bearings are the cause of the issue. Not everyone will be able to identify the precise reason why a washing machine with a direct drive started to knock, and the "symptoms" won’t be obvious enough. Wear indicators may show up on the rear of the tank as the unit ages more. Additionally, there is a noticeable backlash when manually rocking the drum, and the machine will hum and make noise akin to a rocket engine when it is spinning. It is simpler to diagnose a breakdown when there are such clear indicators.
The LG machine’s bearings must be changed as soon as possible; if not, the shaft will gradually collapse and a full replacement of the tank-drum unit will be required.
Assemble the parts and tools required for the repair before beginning work on the machine. First, a direct drive washing machine needs to have its seal and bearings purchased. It’s critical to ascertain the make and model of your "home assistant" and purchase the appropriate replacement parts. The following are some instances of the component sizes needed for specific machines:
- models F 1068 LD, LG WD 1030 R, WD 1274 FB, WD 8022 CG, WD 8023 CB, WD 8050 FB, WD 8074 FB, WD 10130, WD 10150 S – oil seal 37x66x5/12, bearing 205-206;
- LG WD 1050 F, LG WD 1074 FB – oil seal 35.75x66x5, bearing 205-206;
- LG WD 6002 C, LG WD 6007 C and WD 6212 – oil seal 25x50x10, bearing 203-204.
An oil seal: what is it? This sealing ring keeps water out of the bearing. Most of the time, the unit breaks down because of damaged rubber. Wear is accelerated if the gasket develops cracks because the liquid seeps to the metal components and washes the grease away.
To replace the parts on your own, get the inventory ready:
- screwdrivers (positive and negative);
- hammer;
- chisel;
- set of wrenches of different diameters;
- pliers;
- WD-40 aerosol;
- metal pin;
- moisture-resistant sealant (required when reassembling the tank).
There must be plenty of room for comfortable repairs. Taking the washing machine to the garage directly is the best course of action. Should this not be possible, take the equipment out of the house communications and move it to the middle of a large room. As soon as the parts and tools are prepared, you can start taking the machine apart.
Removing the tank-drum unit
The plastic tank and drum need to be taken out of the washing machine’s direct drive body in order to replace the bearings. The equipment needs to be cut off from the water supply, sewage system, and network. Disconnecting the inlet and drain hoses from the washing machine’s back wall is necessary. The following will be the subsequent action algorithm:
- drain the water remaining in the machine"s pipes. This can be done by unscrewing the trash filter. It is located at the bottom, behind the base panel of the case. Unscrew the plug and collect the liquid in a container;
- remove the powder receptacle;
- remove the top cover of the case by unscrewing the two bolts that secure it;
- unscrew the screws that hold the control panel. It is not necessary to disconnect the wires, it is better to carefully remove the panel and hang it on a special hook on the side wall of the case;
- open the hatch door, bend back the sealing cuff, pry up the clamp that secures it. Remove the holder ring from the machine;
- unscrew the screws along the perimeter of the front wall, remove the front panel;
- remove the upper metal strip, remove the counterweights;
- use pliers to loosen the clamp of the pipe connected to the dispenser. Remove the tube, pull out the hopper for detergents;
- disconnect the pressure switch nipple;
- disconnect the drain pipe from the washing machine tank. It is secured with a clamp;
- remove the back wall of the machine, removing all the screws;
- take a photo of the wiring diagram, this will help with reassembly;
- unscrew the main direct drive screw. To do this, you will have to fix the motor;
Screwdrivers should not be used to block the engine’s connections because the coils there are easily damaged.
- to remove the central bolt, hold the tank, preventing it from rotating, throw the key with your free hand and unscrew the fasteners;
- remove the electric motor cover;
- reset the electric motor chips, disconnect the wiring;
- remove the engine by unscrewing the screws holding it;
- disconnect the contacts from the heating element, pull out the tubular heater;
- remove the shock-absorbing elements. To remove the damper bushing, press on its latches from the inside and pull it towards you.
Nothing now prevents the unit from being removed. Every component and wire that is attached to the machine’s main tank has been taken out or disconnected. The tank can be raised, taken out of the body, and placed on a level, hard surface by pulling it free from the springs.
| Step | Description |
| 1 | Disconnect the washing machine from power and water supply. |
| 2 | Remove the top and back panels to access the drum. |
| 3 | Detach the drive belt and motor to expose the bearing. |
| 4 | Use a wrench to unscrew the bearing housing. |
| 5 | Carefully remove the old bearing from the drum. |
| 6 | Install the new bearing into the housing. |
| 7 | Reassemble the motor and belt back onto the drum. |
| 8 | Replace the back and top panels. |
| 9 | Reconnect the washing machine to power and water supply. |
It can be difficult to replace the bearing in an LG washing machine with direct drive, but it is definitely possible if you have the right equipment and patience. You can prolong the life of your machine and save money by taking the time to fix it yourself.
Pay close attention to each step and make sure that every component is correctly reassembled. Maintaining your washing machine’s smooth operation and preventing future problems can be achieved by paying close attention to the details.
Always remember that working with appliances requires caution. Always unplug the device, and take care when handling the parts. It’s a wise decision to seek professional assistance if you ever feel uncertain.
