How to disassemble and clean a washing machine?

Your washing machine may begin to smell or perform less well over time. This frequently occurs as a result of debris, detergent residue, and other dirt building up inside the machine. Cleaning and disassembling your washing machine on a regular basis is essential to keeping it operating smoothly.

To do this on your own, you don’t need to be an expert. You can disassemble the machine easily, clean the important parts, and put it back together with a few simple tools and some perseverance. Your washing machine’s lifespan can be increased with this easy maintenance schedule, which will also guarantee that your clothes always come out clean and fresh.

Where the main dirt is going?

Although the washing machine is filthy all over, certain areas tend to collect the majority of the scale and trash. It is sufficient to determine which areas are the most littered and to clean them in that order. The following are the "sick points" of the machine gun that we are discussing.

1. Garbage filter. This name is not accidental – it is on this nozzle that about 90% of the garbage washing in washing. It must be cleaned first.

Sora’s washing machine has a 90% waste filter buildup.

1. Luke"s cuff. In the folds of the rubber seal, IA and extraneous objects accumulate. The situation is complicated by the fact that, in addition to garbage, water also gets into the elastic band, which, with a long drying, leads to the appearance of mold and fungus.
2. Pump. More precisely, the impeller of the pump, on the blades of which “love” to wrap hair, pile and wool. Less often, the “wheel” is blocked by large debris that has leaked through the drain filter.
3. Detergent tray. The powder left in the dispenser hardens and over time becomes covered with mold and limescale. If the hopper is not cleaned, the pipe will become clogged and will stop pouring soapy liquid into the tank.
4. Tank bottom. Debris inevitably accumulates on the bottom of the main tank. To clean it, you will have to partially disassemble the machine.

After determining which areas of the machine are most susceptible to debris buildup, we start a thorough cleaning. Although you can complete the task on your own, there may be times when you will require assistance from a spouse or friend. You’ll need screwdrivers, a rag, water, soap, and WD-40 for the "cleaning."

Cleaning the "trash can"

You must clean the trash filter first. The "trash can" is usually found in the lower right corner of the front of the body. Usually, a decorative door with a round or rectangular shape hides the nozzle. Reaching the drainage is simple if you follow these instructions:

• tilt the body of the machine back so that the front legs rose into the air by 5-7 cm;
• place a small container under the technical hatch to collect water;
• pry up the hatch with a screwdriver, unfasten the plastic latches and remove the door;
• inspect the filter, black or blue plug, and emergency drain hose, orange or red;
• pull the hose and drain the water into the basin;
• if there is no drain hose, then unscrew the trash filter counterclockwise, getting rid of the water;

After the high-temperature cycle ends, it is not permitted to empty the machine through the trash filter right away because the water won’t have time to cool down and will burn!

• unscrew the "trash can" completely;
• assess the condition of the seat and the filter itself;
• clean the nozzle from debris and scale.

It will be necessary to soak a heavily soiled filter in a warm lemon solution. The machine goes back to where it was when you screw the clean nozzle back in.

To keep a washing machine operating efficiently and prolonging its life, it must be disassembled and cleaned. You can completely clean places where dirt, mold, and detergent residue tend to accumulate by carefully removing important parts like the detergent drawer, filter, and drum. Frequent cleaning keeps your machine operating smoothly and guarantees that your clothes come out fresh. It also averts offensive odors and potential malfunctions.

Powder receiver compartments

Cleaning the powder container is likewise simple. However, you must take it out of the case first. Here’s how to go about it:

• pull the tray towards you until it stops;
• without letting go of one hand, press the plastic tab, mostly blue, located in the central compartment for rinse aids with the other;
• pull the hopper out all the way.

The powder container should be soaked for one to two hours in a cleaning solution before cleaning.

It’s simpler to determine the level of contamination and begin cleaning after removing the tray. You must soak the plastic for some time in order to remove the hardened powder; simple rinsing will not do. This approach has shown to be effective:

• fill a basin with water heated to a temperature of no more than 60 degrees (plastic deforms and deteriorates in boiling water);
• dissolve 200-250 g of citric acid or 100 ml of vinegar in water;
• lower the powder receptacle into the solution so that the tray is completely covered with water;
• wait at least 1.5 hours.

After removing the powder container that has been soaked from the solution, we mechanically clean it. The main job is to use toothpicks or an old toothbrush to remove any remaining powder and debris. We wash the hopper and use a rag to wipe it dry at the "finish."

Cuff

It is easy for dirt and plaque to get on the hatch cuff. Dirt, lint, and detergent particles typically collect in the lower seal area between the folds. You must open the drum, pull back the rubber, and thoroughly clean all of the difficult-to-reach areas in order to remove accumulated debris. For these uses, a soft cloth or dish sponge are employed.

If the hatch cuff is not cleaned promptly, mold grows and damages it.

We move on to the second step, which is the application of a cleaning agent, after the first surface cleaning. After dousing the sponge with bleach, vinegar, or lemon solution, cover the entire cuff. After that, the door is shut for 30 to 40 minutes so that the preparation can finish the process of dissolving deposits and fungus-free rubber. The drum is cleaned with fresh water and wiped dry after 30 minutes.

It’s crucial to use the appropriate cleaning solution when cleaning the cuff. Caustic and excessively aggressive acids are not allowed to be used because they harm rubber.

Cleaning the pump

When hair or other debris gets trapped in the pump’s impeller, cleaning it becomes a little more challenging. Since the pump needs to be taken out and disassembled, you will need assistance from an outsider in this situation. To gain access to the back wall, first unplug the washing machine from the communications and move it away from the wall. Next, we begin cleaning the body by fastening the hoses to it:

• make sure there is no water in the detergent tray;
• carefully turn the machine over onto its right side;
• look under the bottom of the washing machine and look for the pump – a round black part located on the snail and screwed with four bolts;
• take a photo of the location of the screws and wires;
• release the pump by disconnecting the wiring and unscrewing the fasteners;
• swing the pump and remove it from the snail.

The pump’s impeller should rotate, but it should do so with noticeable effort rather than freely.

Next, evaluate the impeller’s state. The blades, though in good shape, spin with a noticeable resistance. The wheel needs to be free of lint, hair, and threads if it is immobile. Free rotation is abnormal; it looks like the component has flown or fallen off the axis. There are two options: either replace the pump with a new one or tighten the fastening even more. The most important thing is to avoid attempting to "fix" the device using glue or sealant, as this kind of design is dangerous and unreliable.

We disassemble the pump if the impeller is operating as it should. After removing the housing and cleaning any dirt from the two halves, reassemble and test the blades. Non-separable pumps can only be fixed by replacing the spare part entirely; they cannot be split in half.

You can keep your washing machine operating efficiently and greatly increase its lifespan by taking the time to disassemble and clean it. You can get rid of any hidden debris, detergent residue, and built-up dirt that might be causing bad odors or performance problems by carefully following the instructions.

To ensure that everything fits back together properly, always unplug the machine before beginning any work. You should also keep track of the screws and parts you remove. Frequent cleaning ensures that your clothes are washed in a hygienic environment in addition to maintaining the performance of your machine.

Make sure everything is working properly by doing a test wash without any laundry after you’ve put the machine back together. Your washing machine will provide you with good service for many years to come with regular maintenance like this.

Video on the topic

Repair and cleaning of an inverter WASHING MACHINE – LG.

Dismantling a washing machine (using the LG F 1068LD as an example)

Every housewife should know about this life hack with a washing machine

how to disassemble a Hotpoint Ariston washing machine