Error F05 in the WHILPOOL washing machine

It can be annoying to deal with an error code on your washing machine, especially if it interferes with your laundry schedule. Knowing the meaning of the F05 error code and how to fix it is crucial if your Whirlpool washing machine displays it.

Usually, this error code indicates a drainage issue, which can hinder the proper operation of your machine. Thankfully, the problem is frequently resolvable with a few easy steps.

This post will explain the causes of the F05 error, how to fix it, and what you can do to get your washing machine back up and running.

All attention to the heating element

Faults on Fridays point to issues with water heating. The automatic machine Virpool’s heater is inspected first. The heating element is situated directly beneath the tank at the base of the washing machine.

A multimeter is used to check the automatic machine’s tubular heater.

In order to diagnose the heater on your own, you should:

• pull the power cord of the washing machine from the socket;
• close the damper responsible for the water supply;
• disconnect the washing machine from utilities;
• move the machine away from the wall or furniture to have free access to the back of the case;
• use a screwdriver to unscrew the screws securing the back panel of the washing machine;
• remove the wall, find the heating element;
• take a photo of how the contacts are connected to the heater (this will help to avoid mistakes during reassembly);
• remove the wires connected to the heating element;
• turn on the tester, switch it to ohmmeter mode;
• attach the probes of the measuring device to the terminals of the heating element and evaluate the readings on the display.

The resistance of a functional heating element should be between 26 and 28 Ohms. An internal break will be indicated by a unit on the multimeter screen, and a short circuit will be indicated by a zero. In this instance, a replacement of the tubular heater is required as repairs are not possible.

The heating element is inspected for damage if the resistance is within normal limits. The probes of the multimeter are placed on the terminals after it has been set to the continuity test mode. The element needs to be changed if the tester beeps when it comes into contact with the heater.

Disassemble the old heating element after determining that a replacement is necessary. This could be challenging because the heater’s protective seal gets louder over time and gets in the way of the part being removed. Follow these steps:

• treat the rubber gasket with WD-40;
• wait 15-20 minutes, let the lubricant work;
• disconnect the temperature sensor;
• unscrew the nut securing the heater;
• press the threaded bolt inward;
• rock the heating element and remove it from the washing machine housing.

For a particular model of Whirlpool washing machine, a new heater is bought. It is preferable to take the old heating element to the retailer and request that the seller choose an analog one. It is worth cleaning the seat to remove scale and dirt before installation.

Let"s test the thermistor

If the heating element is working perfectly, what should you do? One possible source of the error F05 is a malfunctioning temperature sensor. The thermistor is situated in the space between the heating element’s contacts.

The main control module receives the temperature reading of the tank’s water from the thermistor.

Take out the temperature sensor from the heating element in order to perform diagnostics. A multimeter is then used to check the thermistor after that. The following will be the sequence of events:

• turn on the multimeter in ohmmeter mode;
• press the tester probes to the sensor terminals;
• lower the thermistor in hot water (so that the contacts remain dry, do not allow them to get wet);
• evaluate the readings on the tester display.

When submerged in 50°C water, the sensor should register resistance of approximately 1350 Ohm. The multimeter display’s readings will drop as the liquid cools. The thermistor isn’t working properly if the numbers on the device’s display are significantly different from the ones that appear on standard devices and stay the same. Itisnecessarytoreplacethethermostatbecauseitisbeyondrepair.

One buys a new thermistor from a specialty retailer. Make sure the replacement parts you buy online are made specifically for your Whirlpool washing machine. The installation of the thermostat is done in reverse order.

In Whirlpool washing machines, error F05 usually indicates a drainage problem, which is frequently brought on by obstructions or a broken pump. You can save time and money by comprehending this error and learning how to troubleshoot it.

To begin with, make sure there are no obstructions in the drain hose or filter that could be stopping the water from draining correctly. Regular cleaning of these parts can stop this error from happening again.

If the problem persists after removing the obstruction, the pump may be broken. In this situation, to make sure your washing machine gets back to its best working condition, you might need to think about replacing the pump or getting professional help.

Whirlpool washing machines that display error F05 typically have a problem emptying the water, which is frequently caused by a clogged filter, a blocked drain hose, or a broken pump. It’s critical to fix this error right away in order to stop additional damage and restore your machine’s functionality. Knowing how to locate and resolve this problem can help you save time and money by preventing needless repairs.

Video on the topic

Error F5 of the Atlant washing machine. 10.11.23

F05 does not drain water well, Whirlpool washing machine, official service center DeutschMechanica Kyiv

Ariston washing machine, error F05. The washing machine does not drain water

Indesit washing machine error F05. All problems with water and their elimination

Whirlpool washing machine error F 05.Changing the temperature sensor

Resetting the error of the Whirlpool washing machine