Electrolux dishwasher does not fill with water

When the water in your Electrolux dishwasher runs out, it can quickly throw off your daily schedule. When a dishwasher malfunctions, it requires more time to wash dishes by hand, which is a chore that nobody enjoys. Although this frequent problem can be annoying, the good news is that you can usually resolve it on your own.

The issue could be caused by a number of things, such as a malfunctioning float switch or a blocked water inlet. The first step to getting your dishwasher back in working order is figuring out what might be wrong. Let’s look at a few of the most typical causes of your Electrolux dishwasher not filling with water as well as some solutions.

The dishwasher requires maintenance

This problem typically arises from common carelessness or from failing to follow the dishwasher’s maintenance and operation guidelines. Make sure the water supply is normal and that the tap is working before anything else. It makes sense that the dishwasher won’t function without water if the water supply isn’t operating right now.

Additionally, confirm that you have only ever loaded the "home assistant" with premium detergents. Improper choice of household chemicals can have a negative impact on dishwashing speed as well as quality. Try not to economize on detergents and stick to tried-and-true household chemicals to avoid this.

The water supply valve, which is situated where the hose attaches to the water supply, should lastly be checked. Maybe you closed it earlier and forgot to open it.

Malfunctions that stop water intake

If all of the manufacturer’s instructions were followed, the "home assistant" was operated appropriately, and there are no issues with the water supply, it is worthwhile to progressively investigate the most typical causes of the irregular water intake. The most popular choices, according to experts, are as follows:

• the flow filter or the entire dishwasher system is clogged;
• the inlet valve is damaged, due to which the water supply is blocked;
• the door mechanism is broken, due to which it is impossible to hermetically close the machine;
• the pressure switch is faulty;
• the "Aquastop" leak protection has been triggered;
• the control board has failed.

We will address each of the listed reasons in detail.

Is the filter element clogged?

Regretfully, the majority of Russian cities do not have the purest or softest water. Very hard water has a lot of impurities, which can easily clog the dishwasher filter. Water will either not be collected at all or will be collected very slowly as a result of the obstruction.

The filter itself resembles a tiny mesh and is made to stop abrasive particles and contaminants from the water supply from entering and damaging expensive machinery. If it is clogged, it is simple to clean.

1. Turn off the water supply.
2. Unscrew the water supply hose.
3. The mesh is located in the place where the hose connects to the dishwasher.
4. Clean the filter with a small needle, cleaning it from the blockage.

The filter mesh can be immersed in a citric acid solution for an hour to get the best results.

Install the element in its designated location after cleaning, making sure to follow the directions in reverse order. Examine the machine’s functionality. If the issue still exists, move on to the next diagnostic phase.

Is the inlet valve working?

You shouldn’t expect any water supply from it if the water supply valve is damaged. Once it gets the proper signal in such a case, it will just stop opening. If it is required to operate continuously under conditions of fluctuating voltage or water pressure, it may malfunction.

It is highly unlikely that this can be fixed if it occurs. You will need to purchase a new part and install it in place of the damaged one in order to restore normal operation of the "home assistant." It would be best to call a service center specialist so that he can perform the repair himself, as this procedure can be quite challenging for those without specialized training or experience.

The dishwasher "does not know" how much water has already been collected

The control board’s inability to determine the amount of water that has already been collected and how much more needs to be added is another frequent issue. This occurs when the water level sensor breaks, causing it to either stop sending any water level information at all or send the control unit inaccurate data. As a result, the water intake stops when the control model decides that the data from the pressure switch is false. This is done for safety reasons by the module.

If you have an ordinary multimeter at home, you can diagnose the sensor on your own. Simply pay close attention to what we say.

• Disconnect the dishwasher from the power supply and water supply.
• Turn it on its side.
• Remove the lid from the bottom of the dishwasher.
• Find the pressure switch, which resembles a plastic washer.
• Use pliers to remove the tube from the element.
• Use a screwdriver to unscrew the retaining screws, disconnect the wires and remove the sensor.

Remember to snap a picture of the wiring so you have it as a reference when you reattach the component.

• Switch the multimeter to ohmmeter mode and check the resistance of the element by connecting the tester probes to the sensor contacts.

The only thing that will help if the water level sensor is truly broken is replacing it with a brand-new pressure switch.

There are several straightforward to more complicated reasons why your Electrolux dishwasher might not be filling with water. These include a kinked water supply hose, a blocked inlet valve, or a malfunctioning control board. Determining and resolving these issues requires a methodical process.

The electronic board requires attention

A malfunctioning electronic board in the Electrolux dishwasher is one of the most unpleasant causes of the issue. It is in charge of obtaining data from other home appliance units and transmitting commands to every component of the apparatus. Thus, the device as a whole will cease to function if the control unit malfunctions. Since fixing this issue on your own is nearly impossible, you’ll need to get in touch with the service center and hope that the element can be fixed rather than having to buy a new one.

You are limited to examining the control module’s functionality in this scenario. To accomplish this, adhere closely to the plan’s instructions.

1. Open the bunker door.
2. Unscrew all the bolts on the door.
3. Find the control board.
4. Inspect it for damage, such as burnt wires and tracks.

Should you notice any of these "symptoms," you should stop using the dishwasher altogether and get professional assistance. It is preferable to leave diagnostics and repair to the expert rather than attempting to inspect the component yourself because issues with the electronic module are not always obvious.

If water isn’t filling your Electrolux dishwasher, it’s critical to fix the problem right away to prevent more problems. Make sure the water supply is working, the valve is fully open, and the inlet hose isn’t kinked or obstructed.

If the water supply is working properly, there’s a chance that internal dishwasher parts are the issue. A malfunctioning water inlet valve, float switch, or even door latch could keep the machine from operating as intended. A professional may need to inspect or replace these parts.

You can avoid the inconvenience of a broken dishwasher by taking the time to troubleshoot and fix these common problems. To help you get your Electrolux dishwasher back in working order, don’t hesitate to contact a qualified technician if you’re unsure or uncomfortable doing repairs yourself.

Video on the topic

Electrolux dishwasher does not fill with water. Error i20 and F0.

How to check the solenoid valve in a dishwasher

Dishwasher inlet valve. Dishwasher valve does not work. Water does not fill.