It can be a little scary to set up a new dishwasher, particularly if it’s your first time using a Dexp model. However, with the correct instruction, you’ll be washing dishes in no time. The secret to getting the best results is knowing how to turn on the machine, regardless of how big of a load you have after dinner or how small you just have a few cups and plates.
We’ll go over how to start your Dexp dishwasher in this post so you can be sure your dishes are always spotless and clean. We can assist you with everything from turning it on to choosing the appropriate cycle.
| Step | Description |
| 1 | Ensure the dishwasher is properly connected to power and water. |
| 2 | Open the door and load your dishes, placing them securely in the racks. |
| 3 | Add the correct amount of detergent to the dispenser. |
| 4 | Close the door firmly until it locks into place. |
| 5 | Select the wash cycle using the control panel. |
| 6 | Press the start button to begin the wash cycle. |
Why run the dishwasher without dishes?
The manufacturer advises operating the dishwasher in test mode, or idle start, prior to filling it with dishes and turning it on full. Some users do not think this is a good idea, but they are mistaken. We will provide multiple arguments to substantiate our claims and show why an idle start is required.
- During the first flush of the equipment with water, debris that may accidentally get into it during installation, as well as grease residues, is removed.
- A test run allows you to make sure that the water is collected quickly, warms up well, drains completely after the end of the cycle, and check whether the drying is done well. That is, it gives the opportunity to find out whether the machine is functioning properly.
- It is also an opportunity to make sure that the equipment is installed correctly. There are examples when during installation the electrical wire was pressed down by furniture, so the unit could not even be started.
Kindly take note! Some people think you shouldn’t use detergent in the dishwasher while it’s being tested. This is a typical error. Recall that using detergent and salt is essential!
You must remove the lower basket, which is found at the bottom of the appliance, in order to access the salt compartment. Lift the cover, add half of the 1.5 kg pack, and then add more salt to the compartment. Be careful not to fill the reservoir to the brim; it should not be full. It’s not frightening that extra liquid will leak into the tank when you add salt.
The next thing to do is choose the dishwashing solution you want to use. Each of these products has a dedicated space on the inside of the door. After that, you ought to switch on the Dexp dishwasher and select the proper setting.
Additionally, you must choose the water hardness parameters prior to beginning the wash as this feature influences the quantity of salt used. The simplest method for determining hardness is to use test strips; alternatively, you can get information from your neighborhood Vodokanal. The last step is to choose the preferred mode and hit "Start."
Make sure the Dexp dishwasher is plugged in, load your dishes, and add detergent before turning it on. Next, use the control panel to select your preferred wash cycle, then hit the start button. Your dishes will be spotless with little effort because the machine will start the cleaning process automatically.
We start the PMM in normal mode
The dishwasher functions properly, the test switch-on was successful, and everything went according to plan. Don’t rush to put dishes in it and begin washing them right away, though. You ought to give it some time to cool down.
Crucial! Overuse of the pump and heating element can result from too many equipment starts.
After some time, when the dishwasher has cooled down, place the dishes in it. It should be pre-cleaned from food residues. Load the detergent into the appropriate compartment. Rinse aid and salt are already in the compartments, in most cases they are enough for a couple of months. The quality of washing will be maximum if you take care that the dishes and cutlery are correctly laid out in the baskets, and at the same time nothing prevents the access of water to any area of the chamber and the movement of the rocker. After you make sure that everything is in its place, you need to select a program and press the "Start" button.
It might take you longer to arrange the dishes when using the machine for the first time. But don’t worry, you’ll soon be doing this on your own. And you’ll be happily surprised by how much extra time you have after hiring such a "assistant."
Once you know the procedures, setting up your Dexp dishwasher is easy. You can make sure your dishes are spotless every time by using the proper procedure.
The secret is in the details, from loading your dishes correctly to choosing the right settings. Your dishwasher handles the rest with a few clicks.
Thus, the next time you’re ready to clean up, keep in mind how simple it is to let your Dexp dishwasher take care of the task, adding a little convenience to your life.
