You may find it annoying and perplexing when your Indesit washing machine refuses to stop washing. It appears that the machine is stuck, spinning or rinsing nonstop, rather than ending its cycle and allowing you to continue with your day.
This problem is more frequent than you may imagine and has multiple potential causes. Finding the source of the issue is the first step towards resolving it, whether it is a straightforward setting error or a more complicated mechanical issue.
This post will examine potential causes of this problem and provide workable fixes to enable you to resume using your washing machine as usual.
- The reason for the machine to cycle
- Made a mistake with the drain connection
- The filling path is clogged
- The level sensor is acting up
- Inlet valve
- Thermistor or heating element
- Video on the topic
- INDESIT washing machine. Spins without stopping Handle Program switch. DIY repair
- If the washing machine washes endlessly
- If the INDESIT washing machine does not finish washing, stops without finishing the program.
- Indesit washing machine fills with water but does not wash
- Indesit WIUN 102 washing machine. Pours water without stopping.
- The washing machine does not turn off and washes for a very long time without spinning
- The washing machine washes for a long time, does not heat, constantly adds Causes, repair
The reason for the machine to cycle
Modern washing machines have "recorded" programs in their memory that let you choose the best washing settings based on the kind of laundry. The duration of each mode varies.
You should exercise caution if the machine you started continues to operate after the allotted amount of time.
Testing the washing machine should be done once the cycle has finally ended. Launch the shortest program and watch the computer as it operates. Observe any one of the following symptoms:
- the washing machine takes a very long time to fill with water. This may be due to weak pressure in the communications, a clogged inlet filter, a kink or defect in the inlet hose. Perhaps the inlet valve is clogged, but then the machine will not start filling with water and will hum;
- the machine fills the tank with water and immediately drains the liquid from the system. Then the wash may continue indefinitely. In this case, the unit is probably not connected correctly. Perhaps the problem lies in the failed pressure switch;
- the draining takes a very long time. This may be due to a clogged waste filter, pump, drain hose, sewer, branch pipe, etc.;
- the cycle is extended due to long heating. A layer of scale on the heating element prevents heat transfer. Also, the thermostat may be damaged;
- the equipment “freezes” precisely at the heating stage. This means that the problem is in the heating element, it has failed and does not start heating the water;
- the machine “loops” several times during the cycle. Most likely, the main control unit is not working correctly;
- the drum cannot accelerate to the specified speed, or it picks up speed too slowly. Most likely, the maximum permissible load weight of the equipment has been exceeded or an imbalance has occurred.
It should not be difficult to determine the primary "symptom" of the malfunction by closely examining the machine. After determining the reason for the extended washing, let’s decide what to do.
A broken timer, a problem with the water level sensor, or a malfunctioning control board could be the cause of your Indesit washing machine’s continuous cycle. If you take care of this issue right away, you can save more damage to your machine and make sure it starts up smoothly again.
Made a mistake with the drain connection
You should first examine the water pressure in the faucet. It makes perfect sense why the cycle is delayed if it is extremely weak. You ought to hold off until the supply is restored in such a circumstance.
The liquid will gather and quickly drain from the system if the drain hose is connected to the sewer incorrectly. The control module will receive a signal from the pressure switch informing it that there is not enough water, and the "brain" will then issue the order to refill the drum.
You must inspect the drain hose’s connection. It must be situated 50–60 centimeters above the ground. Gravity will take the liquid out of the system if the distance is shorter. In order to prevent the issue of water unexpectedly flowing out of the tank, it is advised that you connect the drain hose via a siphon rather than straight into the sewer.
The filling path is clogged
A cycle delay may also result from an overly lengthy water intake. As a result, you must examine the filling system in great detail. Examine the filling hose to see if it has kinked or been pinched by something foreign. Next, carry out the following actions:
- de-energize the washing equipment;
- disconnect the filling hose from the washing machine;
- wash its cavity under running water;
- remove the filter mesh, remove all dirt from it. If there is rust on the element, soak it in a solution of citric acid;
- install the filter and hose back in place.
- disconnect the machine from the mains, turn off the water supply;
- unscrew the trash filter, it is located in the lower right corner of the body behind a special panel. Before removing it, it is better to cover the floor with rags, as liquid will flow out of the hole;
- clean the filter element, remove debris from the hole;
- put the trash filter back in place;
- disconnect the drain hose, rinse it under running water.
You’ll need to investigate further if clearing the drain filter and sleeve doesn’t help. The washing machine must be turned upside down in order to inspect the pump pipe. Locate the pipe, release the clamp that holds it in place, and take the hose off the pump. After cleaning, the pipe is fixed in position.
The level sensor is acting up
The pressure switch’s failure is the next factor keeping the cycle going. When this happens, the level sensor either stops working altogether or gives the "brain" the erroneous signals. The control module does not send out a signal to begin washing because it is unaware that the machine has already filled with the necessary amount of liquid.
You should de-energize the washing machine and shut off the water supply valve before beginning any repairs.
To manually swap out the pressure switch:
- remove the top cover of the case, to do this, unscrew the two bolts holding it;
- find the pressure switch;
- disconnect the level sensor contacts, disconnect the pressure hose, remove the fastening screw;
- install a new part, connect in the reverse order.
How can I determine whether the pressure switch needs to be changed? The sensor is located beneath the cover. Remove the tube from it, place another tube on the nipple, and gently blow into it. If there’s a click, the element’s mechanics are working properly. You will know about the pressure switch malfunction if there is total silence.
Inlet valve
For an extended period of time, an electromagnetic valve malfunction could also be the cause. Its membrane "jams," allowing water to enter the tank without restriction. Repairing the inlet valve is useless; a full replacement is required. The following is the action algorithm:
- remove the top cover;
- find the valve, it is located near the back wall;
- disconnect the contacts and all hoses from it;
- unscrew the fixing bolts;
- pull out the old valve;
- install and secure the new part, connect the hoses and wiring.
This concludes the breakdown quick diagnostics. You will need to go further if you are still unable to solve the issue.
Thermistor or heating element
Hard water can cause scale to build up on the washing machine’s heating element. As a result, the element’s heat transfer is violated. The water takes a long time to heat up to the desired temperature.
To try to get the scale off the heating element, try the following:
- remove the top cover, dismantle the back wall of the case;
- disconnect the heating element contacts;
- loosen the central nut, push the screw;
- remove the heating element.
Next steps, what should I do? A variety of reagents are available to remove scale. Another option is to try cleaning the surface with common household products. For instance, if you soak the area in a citric acid solution for a day, the plaque ought to come off with ease.
Make sure to use a multimeter to check the heating element; if a malfunction is found, the component will need to be replaced.
One possible cause of the cycle’s persistence could be a damaged temperature sensor. The "brain" of the system turns off the heating element when the water reaches the desired temperature, which is signaled to the control module by the thermistor. The thermostat is housed in the heating element’s housing; if it isn’t functioning properly, the sensor needs to be changed.
Problem | Possible Causes |
Washing cycle does not stop | Timer malfunction or control board issue |
Drum keeps spinning | Faulty sensor or pressure switch |
Water keeps filling | Defective inlet valve or water level sensor |
Machine stuck in rinse | Drain pump or filter blockage |
Though it can be annoying, most Indesit washing machines can be fixed if they are caught in an endless wash cycle. Sometimes the issue can be easily fixed by checking simple things like the door lock, filter, or drain hose.
If these simple solutions don’t work, though, it might be time to investigate more thoroughly if there could be a problem with the machine’s control board or sensors. To stop additional damage to your appliance at this point, it might be best to call in a professional.
By taking care of the problem as soon as possible, you can avoid more serious problems later on and make sure your washing machine functions properly once more.