Although taking out the drum from a Samsung washing machine may seem difficult, it is actually quite possible to accomplish with some help. Knowing how to remove the drum can help you save time and money whether you need to replace a worn-out one, take care of a repair, or clear out any hidden debris. Depending on your particular model, this process may differ slightly, but the fundamental steps are usually the same.
First, make sure your washing machine’s water and power supplies are disconnected. Working with electrical appliances requires utmost safety. To access the drum, first turn off and disconnect everything. Then, open the washing machine. This typically entails taking out the front panel in addition to the top panel.
The next step is to remove the different parts that secure the drum. This covers the agitator (if your model has one), the drive belt, and any hoses that are attached to the drum. Along the way, be ready to remove a few clips and screws. It’s crucial to keep track of these tiny components so you can later put everything back together.
After removing every attachment, you can finally gently lift out the drum. It’s a good idea to use safe lifting techniques or enlist the assistance of someone because it might be heavy. After the drum is removed, you can either finish the necessary tasks or just give the area a thorough cleaning.
The procedure is the same when reinstalling the drum in reverse. You can quickly get your washing machine up and running smoothly by taking your time and carefully following each step. Regardless of whether you’re an amateur do-it-yourselfer or simply taking on a necessary repair, this guide should help to ease the process.
| Step | Description |
| 1 | Turn off and unplug the washing machine for safety. |
| 2 | Open the washing machine door and remove any clothes or items inside. |
| 3 | Use a screwdriver to remove the screws from the door seal or gasket. Carefully detach the seal from the door opening. |
| 4 | Locate and remove the screws or bolts that secure the front panel to the machine. You may need to lift or remove the front panel to access these. |
| 5 | Take off the front panel to expose the drum and other internal parts. |
| 6 | Disconnect any hoses or wires attached to the drum assembly. Note how they are connected for reassembly. |
| 7 | Remove the drum by unfastening any additional screws or bolts holding it in place. Gently lift the drum out of the machine. |
| 8 | Check for any remaining parts or obstructions and carefully remove them if necessary. |
| 9 | Reassemble the washing machine by reversing these steps, ensuring all parts are securely attached. |
Don"t rush to get to work
Without completely damaging the machine, removing the washing machine’s drum is not a difficult task. The most important thing is to disassemble with care and constancy. The following actions must always be taken as part of the preparation process:
- determine a place for disassembly;
- study the washing machine instructions, electrical circuit and other technical documentation;
- collect the materials and tools necessary for the work;
- prepare the equipment for the upcoming disassembly.
Finding a good space for disassembly should come first. This should be a roomy, well-ventilated, well-lit space with a minimum of 4 square meters of free space. It is best to move the washing machine to the workshop or garage. Rags or old newspapers must be spread across the floor to prevent heavy pollution and "flooding."
Remember to take safety precautions when disassembling a Samsung washing machine!
Next, get ready the inventory needed for the subsequent disassembly and repair:
- screwdriver or a set of screwdrivers (slotted and Phillips);
- a set of wrenches and an 8 mm Allen key;
- pliers;
- pliers;
- multimeter;
- impact wrench;
- hammer;
- chisel;
- marker;
- WD-40 lubricant-cleaner;
- sealant;
- CV joint type grease;
- rag;
- basin or other container.
It is preferable to handle the video or photo recording if you intend to reassemble the machine. Acting in reverse order makes it easier to trace your manipulations in this scenario and restore the equipment to its original state. Below, we will explain the disassembly procedure.
Although taking out the drum from a Samsung washing machine can seem difficult, it is doable if you follow a detailed, step-by-step procedure. This post will walk you through the procedure, providing helpful hints and clear directions to ensure that you remove the drum safely and effectively. You can handle your washing machine with confidence when you follow our guide, which will make the task easier and less stressful, whether you’re planning a replacement or taking on a repair.
Step-by-step instructions
If you follow these steps carefully and consistently, disassembling a Samsung washing machine and removing the drum by hand is not difficult. You are now ready to work after gathering all the necessary equipment and supplies. Following the directions exactly is crucial.
- Disconnect the washing machine from the utilities: power supply, water supply and sewerage.
- Remove the cover. Using a Phillips screwdriver, unscrew the screws holding the "top" located on the back wall of the case. Then push the panel away from you and pull it up.
- Remove the dashboard. To do this, you need to loosen all the provided clamps. The first are located under the detergent tray, the others are located along the perimeter of the control unit. It is not necessary to unhook the wiring: it is enough to carefully put the "board" on top of the machine or hang it on a special side hook. But if desired, the wires can be marked, photographed and disconnected.
- Remove the technical hatch door. It is located in the lower right corner of the case and hides the garbage filter. To remove it, simply pry the panel with a flat screwdriver. Be prepared for the fact that residual water is pouring from the hole (it is advisable to substitute a container nearby or put rags).
- Unhook the front wall. First, you need to loosen the metal or plastic clamp on the hatch cuff by hooking it with a screwdriver, and then bend the seal inside the drum. Then unscrew all the screws along the perimeter of the panel and unhook it from the machine body by 2-3 cm. Through the opened space, disconnect the eyeliner from the UBL from the end or remove the blocker completely.
- Remove all other "obstacles". Disconnect all conductors leading to the drum from the heating element, electric motor, pump and other sensors. It is also necessary to remove the inlet valve and pressure switch from the unit, and then remove the pipe connecting the tank and the powder receptacle. You must act as carefully as possible so as not to damage the elements.
- Pull out the counterweights. Most modern Samsung models have two concrete blocks located under the top cover of the machine. It is necessary to unscrew the bolts holding them. Be careful – concrete is extremely heavy.
- Dismant out shock absorption. First, the lower shock absorbers or dampers that fix the tank are removed. The second springs holding the drum on top.
Recognize that the Samsung washing machine tank is heavy and that it is best to enlist help from more people.
After removing the tank from the unit, it must be placed with the pulley up on a level, dry surface. After removing the engine and weakening the motor’s fixation, disconnect the drive belt.
While disassembling the washing machine, it is advisable to perform a thorough technological diagnostic and verify the functionality of every component. This is where a multimeter comes in handy since it can "call" all the electrical parts. Ten, hoses, the pump impeller, the dispensary, and the garbage filter are among the quickly polluting elements that you can clean concurrently.
Although removing the drum from your Samsung washing machine may seem difficult, it is doable with the correct method. Make sure the machine is unplugged and completely dry before proceeding. Take your time; safety is the most important factor. Take your time and carefully follow each step; if you encounter any difficulties, consult the handbook for your machine for specific instructions.
You’ll need patience and to lift a lot of weight. Disassembling the door seal, front panel, and drum bearings are among the parts that must be removed in order to remove the drum. As you proceed, keep an eye on all the screws and parts—they’re essential for reassembly. Do not be afraid to ask for assistance from a professional if you have any questions or feel uneasy about any step of the process.
After the drum has been successfully removed, you’ll have better access to clean or fix the washing machine’s internal components. Your appliance’s longevity and efficiency may both benefit from this. Recall that routine upkeep and care can keep problems at bay and ensure that your washing machine operates at peak efficiency.
In general, removing drums yourself can be a satisfying do-it-yourself task. You can make sure your washing machine keeps working well for many years to come with a little bit of elbow grease and careful attention to detail. Have fun doing the laundry!
