Is the spin cycle on your Candy washing machine causing it to shake or make more noise than usual? This can indicate that it’s time to replace the shock absorbers. These insignificant but essential parts dampen the movement of the drum during operation, keeping the machine steady and silent.
Although replacing the shock absorbers may seem like a difficult task, you can do it yourself with some help. You won’t need to hire a repair service to get your washing machine operating properly again; this guide will walk you through the process.
Everything from the necessary tools to the detailed instructions for replacing the shock absorbers will be covered in the sections that follow. You’ll be prepared to take on the task with assurance by the end.
- Getting to the dampers
- How to remove a broken or jammed part?
- Related videos
- Replacing the shock absorbers of a washing machine
- How to replace shock absorbers in a washing machine
- Replacing shock absorbers in a washing machine. How to choose and replace them correctly, do-it-yourself repair
- Shock absorber for Electrolux-Candy washing machine. Our code SAR014
- REPLACING SHOCK ABSORBERS IN A CANDY WASHING MACHINE
- Repair of shock absorbers of a washing machine
Getting to the dampers
Usually, all you have to do is watch how the machine operates to figure out when the dampers need to be changed. Household appliances should have their old shock absorbers removed and replaced if they start to vibrate excessively, hum loudly, or jump while being washed.
Use of an automatic CM with malfunctioning dampers should be avoided as this may exacerbate the issue and cause additional harm to the system’s essential parts.
Simultaneously, you should hold off on purchasing new spare parts until the theory of gradually failing dampers has been verified or disproven. How should I handle this?
- Disconnect the equipment from all communications.
- Remove the drain and filler hoses.
- Move the device to the center of the room to get free access to all sides of the case.
- Drain the remaining waste liquid using a drain filter.
- Remove the tray for household chemicals.
- Disconnect and put aside the back wall, having previously removed the fixing bolts.
- Remove the drive belt from the drum pulley and electric motor.
- Disconnect all wires from the engine.
It is best to take a few pictures of the correct wiring connection just in case; you’ll need them for assembly.
- Loosen the electric motor clamps.
- Carefully pry up the fasteners with a screwdriver to press out the stuck joints.
- Finally, carefully remove the motor.
Once the motor is taken out completely, you can begin to replace the dampers. This is due to the fact that they can only be easily taken out of the machine’s bottom. Make sure to use towels or rags to cover the floors before placing the washing machine on its right side.
A Candy washing machine’s performance can be significantly increased and noise levels during the spin cycle can be decreased by replacing the machine’s shock absorbers, which is a simple task. You can replace worn-out shock absorbers on your own with ease using simple tools and a little perseverance, which will save you money and time on repairs.
How to remove a broken or jammed part?
The reason Candy machines’ shock absorbers are so challenging to remove is that they have unique fasteners called expanding plugs, which is why they are also referred to as nails. Such a component directly passes through the plates that support the element at the top and bottom as well as the shock absorber. It is hard to take this expanding plug out of the device because it seems so smooth.
Experts in repair advise against attempting to manipulate the retainer from the opposite side as this raises the possibility of breaking the delicate plastic component. As a result, you must take more devious action and enhance these intricate shock absorber fasteners. How would one go about doing that?
- Take a drill 2-2.5 millimeters in diameter, and 20 centimeters or more in length.
- Using a drill, drill a small hole in the middle of the plug, about three centimeters deep.
- Screw a small screw into the prepared hole so that it remains on the surface for about 4 centimeters.
- Using pliers or a similar tool, clamp the screw you just installed and pull it towards you.
- Carefully remove the screw together with the expansion plug.
- Remove the damper itself from its seat.
The disassembly instructions for the second shock absorber are the same, but you must flip the Candy washing machine over to its left side first. While working, make an effort to locate the perfect drill—both in terms of diameter and length. You will need to disassemble the washing tank and try again if you are unable to remove the shock absorber unit in this manner.
| Step | Description |
| 1 | Unplug the washing machine and disconnect the water supply. |
| 2 | Remove the back panel to access the shock absorbers. |
| 3 | Locate the shock absorbers near the drum. |
| 4 | Unscrew or unclip the shock absorbers from the frame and drum. |
| 5 | Replace with new shock absorbers, securing them in place. |
| 6 | Reattach the back panel and reconnect the water supply. |
| 7 | Plug in the machine and run a test cycle. |
The Candy washing machine’s shock absorber replacement is easier than it might seem. You can save money on repairs by doing it yourself if you have the necessary equipment and a little perseverance.
You can make sure your washing machine operates smoothly, silently, and without experiencing too much vibration by changing the shock absorbers. This easy maintenance procedure can increase the lifespan and general performance of your appliance.
Always unplug the device from the power source before beginning any repairs. You’ll succeed in finishing the task if you take your time and pay close attention to the instructions.
