Error F13 in a Whirlpool washing machine

The F13 error on a Whirlpool washing machine can be annoying and perplexing. This error code denotes a particular problem that must be fixed for your computer to function properly once more.

Knowing what F13 indicates and how to fix it will help you avoid wasting time and further harm to your appliance. The good news is that this error frequently indicates a fixable issue that can be done without the need for expert assistance.

This post will explain the causes of the F13 error and walk you through the steps to fix it so you can quickly and effectively resume your laundry routine.

What does this code mean?

Serious malfunctions are not concealed by error F13. The combination decodes as "malfunctions in the water inlet system," per the instructions. Put simply, the machine is unable to fill the drum to the necessary level. The machine either "thinks" for too long or there is no water supply. In both cases, the board hangs up to prevent overflow because the system cannot complete the command in the allocated time. There are three reasons such a failure happens:

• the central water supply is disconnected or the pressure in it is too low;
• the tap supplying water to the washing machine is closed;
• the powder receptacle or the pipe leading to it is clogged;
• the inlet valve is out of order;
• "stuck" or burned out the control board.

It is best to delay calling a repairman because the control board does not frequently malfunction. The F13 error is typically displayed in cases where the inlet valve is malfunctioning or the detergent tray is clogged. After that, the repair takes a few minutes because the components need to be cleaned or changed.

Prioritizing the exclusion of non-emergency causes of the failure is important. Most likely, the water supply tap is in the closed position or the main water supply in the house has been turned off. Verifying the guess is simple; just check the shut-off valve and other rooms. After making sure everything is clean, we start troubleshooting the Whirlpool washing machine’s filling system.

When a Whirlpool washing machine displays error F13, it usually indicates a wiring or dryer issue, which prevents the machine from adequately drying your clothes. This might be the result of a broken connection or a broken heater. In order to fix the issue and get your machine operating normally once more, it’s crucial to examine the dryer’s wiring and component parts if you’re experiencing this error.

Testing the inlet valve

There’s no need to consider what to do when you see "F13." There’s only one method, and that is to check each filling system component in turn, starting with the inlet valve and moving on to the powder receptacle and control board. Starting with the valve device, which frequently causes errors, is preferable. We carry out the following:

• disconnect the washing machine from the power supply;
• remove the top cover from the housing (unscrew the retaining screws from the back wall, lift the “top” and move it towards yourself);
• find the inlet valve at the junction of the hose and the housing;
• loosen the bolts securing the device and remove the valve from the machine.

Connecting the inlet hose to the device and providing 220V to every coil that is accessible are prerequisites for diagnosing the valve. Water should start to flow and you should hear the distinctive click that indicates the membrane is functioning correctly. If not, there’s a good reason for a longer check.

When using the diagnostic method described, exercise extreme caution. First and foremost, you have to make sure that the live wires are kept dry. Second, you should plan ahead and consider a container for holding water. Any valve that malfunctions when exposed to voltage is broken. Specifically, one of the coils experienced a burnout. Confirming the "diagnosis" is simple: just measure the resistance on the contacts of the device by connecting a multimeter to it. The indicator should typically range between 2 and 4 kOhm. It will be necessary for you to switch devices if there are any deviations.

It is advisable to check the mesh of the inlet valve afterwards. It frequently becomes increasingly clogged with dirt, which stops the water from "passing" through. The problem is simple to solve: take out the filter, wash, rinse, and put it back in its place.

Make sure to inspect the fittings for any pressed-in plastic inserts. They regulate the water pressure that enters the Whirlpool, but they frequently fall in, which makes it challenging to get water into the pool. When this happens, the stream gets too strong, the system recognizes an overflow, and an F13 error is displayed.

It is not possible to fix the inlet valve.

With a broken valve, the Whirlpool cannot be operated. The situation will only get worse if you try to reset the error and ignore the problem. Either a flood occurs or the board freezes due to the weight. It is preferable to not put off the repair.

Whirlpool washing machine error F13 is a frequent problem that can be annoying but is usually fixable with the right technique. Finding the underlying cause is crucial, regardless of whether it has to do with the control board, door lock, or wiring.

You can frequently fix problems without hiring a specialist if you take the time to troubleshoot and take the required actions. Still, it might be best to get help from a qualified technician if the issue doesn’t go away.

You can keep your washing machine in good operating order and save time and money by learning the fundamentals of these errors and how to fix them.

Video on the topic

Ariston washing machine error F13. The washing machine does not heat

Code F13 for whirlpool washing machine –

The Whirlpool Service light is on, washing machine. Lock

Resetting Whirlpool washing machine errors

Whirlpool service mode. Error F13

Repair of the Whirlpool washing machine module error F13

The Service light is on in the Whirlpool washing machine, what to do.