Although disassembling a Haier washing machine can seem difficult, knowing how to do it can be helpful if you need to do repairs or maintenance. Knowing how to disassemble your washing machine can save you time and money, whether you’re fixing a broken part or just want to clean the internal components. You can do this task on your own if you have the appropriate mindset and a few standard tools.
It’s crucial to first assemble the required equipment and familiarize yourself with the machine’s layout. There are several models of Haier washing machines, so it’s good to refer to the handbook that corresponds to your particular model. To prevent electrical hazards and leaks, make sure you unplug the machine and disconnect any hoses before starting.
First, remove the top panel by unscrewing a few screws, if necessary. Depending on what you need to access, you can remove the door or front panel after you get access. As you proceed, keep track of all the screws and parts because they’ll be needed for reassembly. You can examine the inner workings of your Haier washing machine and perform any required repairs by carefully following these steps.
| Step | Description |
| 1 | Unplug the washing machine and turn off the water supply. |
| 2 | Remove the screws on the back panel to access the internal components. |
| 3 | Take off the front panel by removing the screws and clips. |
| 4 | Disconnect the hoses and electrical connections inside. |
| 5 | Carefully detach the drum and other major parts as needed. |
| 6 | Reassemble the washing machine by reversing these steps. |
- Required set of tools?
- We take out everything except the tank
- Video on the topic
- How to repair a Haier washing machine (HAIER) 10kg .
- “How to disassemble a Haier washing machine: user manual” Part one 😉
- Replacing a bearing in a Haier washing machine | 5-minute repair | Haier review
- Replacing bearings in a Haier washing machine || Washing machine repair in Kaluga
- Review of the Haier HW70-BP12969A 7kg washing machine | The module fell off 🙁
- How to disassemble a washing machine? | Washing machine repair for beginners from scratch
Required set of tools?
An automatic machine can be disassembled with a minimal number of tools. In many cases, a single Phillips screwdriver is sufficient for small, superficial repairs. When the washing machine needs to be fully disassembled, additionally get ready:
- screwdriver;
- mallet or small hammer;
- pliers;
- flat-nose pliers;
- puller;
- hex key set;
- slotted screwdriver.
Use a specific liquid WD-40 to loosen fasteners that have become "stuck."
Grease resistant to corrosion is used to loosen the obstinate bolt. You then have to wait ten to fifteen minutes for the liquid to start working. After that, you can remove the screw.
When disassembling the automated machine, you will also require the following tools in addition to those on the list:
- a small container (to drain the remaining water from the machine);
- dry rags;
- marker;
- phone (to photograph the wiring diagram to the parts).
A smartphone can be substituted with a standard camera. The most important thing is to record the work’s advancement on camera in order to avoid making mistakes when reassemblying. Once the required inventory has been assembled, you can start fixing the Haier washing machine.
We take out everything except the tank
If you choose to perform the repair yourself, make sure you thoroughly read the equipment’s instructions. The locations of the washing machine’s components and main units are described in great detail. Make sure you de-energize the automatic machine and close the water supply shut-off valve before beginning any work.
The machine must then have the remaining water drained from it. The drain hose should first be carefully disconnected from the body and its end should be lowered into a sink or bathtub. Next:
- find the trash filter (it is located in the lower corner of Haier washing machines);
- place a container to collect water under the machine, cover the floor around the washing machine with dry rags;
- unscrew the filter element;
- wait until the water drains into the container.
It’s time to start disassembling the washing machine. First, take off the body’s upper cover. You must undo the two bolts holding the panel in place in order to remove it.
The powder container should then be taken out of the machine. Pull the tray out halfway and press the button in the middle of the tray to remove it. The detergent container should then be pulled in your direction.
After that, you can start taking the dashboard apart. Take out all the fastening screws in order to accomplish this. Typically, one bolt is under the powder container and the other is on the other side. With caution, remove the control panel to avoid damaging the buttons, the programmer, or the wires.
Disconnecting the contacts is not necessary if it is not needed. The dashboard can be hung from a hook on the side of the case or carefully placed on top of the machine.
After that, you can start taking the drum door apart. Remove the hatch from the metal hinges by unscrewing the fasteners holding it in place. To prevent breaking the glass, set the door aside on a level surface and place a soft cloth underneath.
The front panel needs to be removed next. You must "hide" the rubber cuff in the drum in order to accomplish this. There are two clamps used to secure it: internal and external. Pulling the outer ring out of the case and dealing with the latch will be necessary. The sealing is then "tucked" into the washing machine.
You can now start taking the front wall apart. Nothing will prevent it from being removed because the dashboard and hatch door have already been removed. Take out the screws on the edges, raise the panel, and take out the hooks holding it in place.
Removing the machine’s back wall is incredibly simple. Since the drain hose has already been disconnected, all that is left to do is remove the panel by unscrewing the bolts and moving it to the side. The body of the Haier washing machine has now been fully disassembled.
Although disassembling a Haier washing machine can appear difficult, it can be done easily with the correct method. By taking the prescribed actions, you can confidently take care of problems or carry out maintenance. Before using the machine, always make sure to unplug it to prevent any electrical hazards.
Keep a close eye on all the screws and parts and meticulously record each step. This will greatly facilitate reassembly. A successful disassembly process requires patience and organization, so be patient and handle each component with care.
It’s a wise decision to consult the user manual or get expert assistance if you run into problems or have questions about any step of the procedure. In the end, a well-kept washing machine will function effectively and provide you with years of enjoyment.
Although disassembling a Haier washing machine can be intimidating at first, it can be easy to do with the correct procedures. This post will walk you through the procedure, dissecting it into easy steps so that you can safely and efficiently disassemble your washing machine for upkeep or repairs. You can resolve any problems and restore your machine’s functionality by adhering to these simple instructions.
