First launch of the Haier dishwasher

Making sure a new dishwasher operates correctly and efficiently starts with its first use. An initial launch that is properly configured can help you prevent problems later on and ensure that your Haier dishwasher operates as intended.

It’s important to know the basic steps involved in preparing the machine for use before you turn it on. This covers every step, from emptying the dishwasher of any packaging materials to properly loading it for the initial cycle.

This guide will help you get your Haier dishwasher up and running without any problems by taking you through all the necessary steps for the first launch.

The Haier dishwasher’s initial launch is a simple procedure that makes sure your machine is configured properly for long-term use. You can ensure that your machine operates effectively right out of the box by following the easy instructions found in the user manual. For your new dishwasher to work as hard as it can, proper installation, loading, and choosing the appropriate wash cycle are essential.

Preparing for the very first wash

Prior to using service repair or returning the equipment to the store, you should always thoroughly examine the household appliances from all angles after unpacking. This will enable you to spot any potential damage right away. If all of the equipment is in excellent shape, you can move on to inspect the entire set, remove the plastic safety clamps, install it, and turn it on.

Make sure the machine is stable and level by paying close attention to this detail.

The main thing is not to rush to start the machine for washing for the first time, because it must first perform an idle working cycle. Such a test is needed for several reasons at once. Firstly, washing without dishes will allow you to clean the insides of the device, which could have gotten dirt, oil, dust and small debris during assembly at the factory. Secondly, the absence of foreign elements in the washing chamber will allow you to evaluate the operation of the device, see all stages of washing in detail, make sure that water steadily enters the washing chamber, heats up, completely goes into the drain, nothing leaks or malfunctions. Finally, an idle start will show the correctness of the installation, because even a minimal deviation from the horizontal level can cause unnecessary noise and vibration.

Chemistry for the first wash

After installation, you can fill the dishwasher with household chemicals rather than dirty dishes because it cannot be turned on without specific detergents if you don’t want to break anything. To ensure the test complies with all regulations, we will require:

• detergent;
• rinse aid;
• special salt for the dishwasher.

With the first, it’s easy peasy; these are common household chemicals that enable household appliances to effectively rid cutlery of grease and other impurities. In total, there are three kinds of detergents:

• liquid in the form of a gel or balm;
• powder;
• tablets and capsules.

Since every kind has benefits of its own, different users select different products for themselves. Because each tablet or capsule is made to last for precisely one working cycle, they are incredibly convenient to use. When a half-load mode is required, this type is the priciest and also the most challenging to operate.

Although powder is more difficult to store, it is far less expensive than tablets and can be used more wisely by adjusting the consumption based on the quantity of dirty dishes. Liquid gels require loading into a designated tank situated on the dishwasher door, just like powder does.

Rinse aid is required so that glassware shines gracefully and clean dishes don’t have streaks after the working cycle. It’s also a good thing that you can expedite the drying process of cutlery with these household chemicals. The dispenser, which is next to the detergent tank, is where rinse aid should be poured.

The latter is most likely a unique salt that aids in softening hard tap water for the dishwasher’s ion exchanger. The big salt crystals prevent scale and limescale from forming on the dishwasher’s essential parts by renewing the resin in the water softener. Such salt needs to be placed into a designated container that is set up at the washing chamber’s base. Housewives occasionally put regular table salt—found in every home—into the salt container, but this is incorrect on many levels. Why are you unable to accomplish this?

• Special regenerating and ordinary salt have different compositions, the former contains much fewer impurities and microelements that negatively affect the elements of household appliances.
• Table salt undergoes fewer degrees of purification, which is also detrimental to the dishwasher.
• Special salt is much larger than ordinary salt, so it dissolves more slowly, which is why it lasts for a long period of time.

Don’t cut corners when it comes to the security and safety of pricey equipment; special salt granules are not as expensive as is often thought. As directed by the following guidelines, add salt:

• remove the lower basket from the washing chamber;
• open the salt bin located at the bottom;
• if this is the first addition of salt, first pour about a liter of water into the tank;
• now pour about a kilogram of salt directly into the water.

Any salt or saline solution residues should always be removed manually or by initiating a working cycle, as they have the potential to cause damage to the chamber’s bottom.

After that, you can put salt out of your mind for a while—this is directly related to how hard your tap water is. By turning on a unique indicator on the control panel, the Haier smart device will alert you automatically when you need to restock on salt granules.

Remember to adjust the salt consumption settings after adding salt. By using specific test strips, which are frequently included with dishwashers, you can determine this indicator on your own. If you don’t have this test equipment or any other, you can check the numbers on the local water utility’s official website. Staff members are obligated to post data on the water supply’s quality as soon as possible.

It’s essential to launch your Haier dishwasher for the first time to make sure everything is configured properly for seamless operation. From turning on the water supply to carefully measuring out the detergent, take your time and follow the instructions carefully. This aids in averting problems later on.

A good way to get rid of any manufacturing residue is to run an empty cycle with detergent. It also lets you to make sure everything is working properly without having to worry about breaking your dishes.

After the first run goes well, you can be sure that your Haier dishwasher is prepared to take care of your everyday dishwashing needs and deliver the efficiency and convenience you’ve come to expect.

Video on the topic

Built-in dishwasher Haier HDWE11-194RU

Review of the built-in dishwasher HAIER HDWE11-396RU

Dishwasher for 60 #Haier HDWE14-094RU

REVIEW of the built-in dishwasher Haier DW10-198BT3RU 💕

Dishwasher Haier HDWE9-191RU

Review of HAIER DW10-198BT3RU from Sulpak

Automatic program in Haier dishwashers: ideal result and ease of use

Haier DW10-198BT3RU dishwasher review