DIY installation of a Siemens dishwasher

Although installing a Siemens dishwasher by yourself may seem difficult, it is entirely possible with the correct assistance. You can reduce service expenses and learn more about your appliance by doing the installation yourself.

Appropriate preparation is necessary before beginning. This include assembling all required equipment, inspecting the installation area, and closely going over the dishwasher’s instructions.

We’ll take you step-by-step through the procedure in this guide to make sure your new dishwasher is up and operating properly without the need for expert assistance.

Features of the selection of components

The set of parts included with the machine is simple to use and can be installed using the standard procedure for a Siemens dishwasher. However, as the installation experts point out, non-standard solutions are needed in roughly half of the cases, necessitating the purchase of extra parts. For example, you will need to purchase an "aqua-stop" valve separately if the inlet hose of that specific dishwasher model isn’t fitted with one.

Exercise caution! The Siemens dishwasher’s "aqua-stop" valve needs to be replaced with either the original Bosch or Siemens dishwasher valve; however, some Siemens models are incompatible with it.

It’s up to you to make the decision because original parts are always a little more dependable and will fit without a doubt, but they are also slightly more expensive than copies. Make a more deliberate choice of the spare part if you wish to save a little money. Purchasing an extended hose from Siemens is also preferable if the standard inlet or drain hose isn’t long enough for you and you want to purchase a longer one.

The issue is that this particular dishwasher model has non-standard fasteners and hoses with an unusual diameter because the manufacturer did not unify many aspects of the development process. Other than that, Siemens dishwashers are dependable, useful, and technologically advanced. This is possibly their biggest flaw. The following tools are required to connect a Siemens dishwasher to a water supply and sewerage system:

• water inlet hose;
• water drain hose;
• stop valve (with two, three or four outlets);
• filters;
• gaskets;
• adapters.

While additional parts might be needed, this standard set is used in the process of connecting to water and sewerage. It should be noted that certain Siemens dishwasher instructions make reference to this.

1. Pressure reducing valve. If the pressure in your water supply system is higher than 1 MPa, then in order to avoid leaks, hose ruptures and other troubles, a pressure stabilizing valve is installed.
2. Electric stabilizer. Through it, the dishwasher is connected to the electrical network in the event that there is a regular voltage drop or, conversely, an increase in such a network – this is an option to protect the dishwasher and other equipment.
3. Additional hose and tap with a filter for connecting to hot water. Some models of Siemens dishwashers have the ability to connect to hot water supply, but there may not be an additional hose, you will have to buy it separately along with the tap, filter, adapters and gaskets.

About the installation location and its dimensions

After selecting the Siemens dishwasher’s parts, we are now installing the appliance in the countertop and surrounding furniture. There may be numerous challenges even when installing a standard dishwasher in furniture; a Siemens machine is a topic for another discussion. Let us examine the expert’s recommendations for how to arrange and measure the dishwasher’s space.

• If you are preparing a place for a fully built-in or partially built-in dishwasher, first carefully measure the model you have chosen. Do not trust the information about the dimensions indicated in the characteristics. Measure each protrusion, in addition, provide a reserve of distance from the walls of the niche to the machine body on the left 2 cm, on the right 2 cm, on the top 1 cm.
• Understand in advance the installation of fasteners for the facade and a metal sheet for protection from steam (if any), after connecting the communications it will be inconvenient to do this.
• Strengthen the floor under the Siemens dishwasher, almost all models of this brand do not like unstable surfaces, unlike, for example, the same Bosch brand. It is also advisable to level the floor, although Siemens are well stabilized and tolerate surface curvature up to 7 0 and more.

Just so you know! Generally speaking, it is preferable to address floor issues head-on and fortify the surface for an extended period of time prior to installing a dishwasher, washing machine, refrigerator, or all appliances together. This will prolong the lifespan of each appliance.

• You should not organize a place for a Siemens dishwasher further than 2 m from the cut-in pipe with water and sewer pipe. The point here is not only in the length of the hose, but also in the inlet valve and pump. If the distance is large, the pump will work much less, and the valve too.

We connect to the water and sewer pipe

You can proceed with the installation if your space-organizing efforts were successful and you are certain that a particular dishwasher model will fit in the space you have created. Connecting the dishwasher to the water and sewer pipes is the next task on the list of tasks to be completed. The Siemens dishwasher can be connected to the sewer in one of two ways: either by connecting the drain hose to the siphon or straight to the sewer pipe. Since it is the more common option, we will take it into consideration.

• First, you need to install a special siphon with a side outlet under the sink. It is designed to connect the drain of a washing machine or dishwasher.
• We seal the thread on the siphon outlet with FUM tape. The FUM tape should be wound not along the thread, but against it, this is more reliable.
• We screw the drain hose to the siphon and proceed to the next stage.

The inlet hose must then be connected to cold water. The sink mixer’s inlet hose must first be removed from the pipe. The tee tap must then be screwed onto the pipe, being careful to seal the connections. On one side of the tee, we screw the mixer’s inlet hose, and on the other, the cleaning filter. Together with the dishwasher’s inlet hose, we screw the aqua-stop valve onto the filter. The task is completed when we screw the other end of the hose into the dishwasher’s inlet valve thread.

Kindly take note! Remember to keep the tap water filter clean after installation. Moving forward, try to clean it once every six months, or once every two months if there’s a lot of sand and other debris in the water.

If you follow a few important steps, installing a Siemens dishwasher yourself can be a fairly simple task. You can save money and enjoy the convenience of a dependable appliance without hiring a professional by making sure that the appliance is placed correctly, making sure that the power and water connections are secure, and adhering to the manufacturer’s instructions.

If you follow the right procedures, installing a Siemens dishwasher yourself can be a satisfying project. Ensuring a seamless installation and optimal dishwasher performance requires careful measurement, space preparation, and handling of the connections.

You may stay away from common problems and take advantage of the convenience of a properly installed dishwasher by paying attention to the little things, like locking the appliance and looking for leaks. Throughout the process, it’s crucial to consult the manufacturer’s instructions to guarantee safety and compatibility.

You can avoid paying for professional installation services and enjoy the satisfaction of finishing the task yourself if you have the necessary patience and tools.

Video on the topic

I am building in a Bosch dishwasher

Connecting a Siemens dishwasher yourself.Built-in dishwasher

INSTALLING THE FACADE IN 5 MINUTES! DISHWASHER!

INSTALLING A DISHWASHER IN A FINISHED KITCHEN / HOW TO INSTALL A DISHWASHER