Siemens washing machine does not turn on

Experiencing a sudden and perplexing refusal to turn on your Siemens washing machine can be frustrating. Your everyday routine may be disturbed by this issue, leaving you with a mountain of laundry and no obvious solution in sight.

This problem could be caused by a number of things, from straightforward electrical issues to more intricate internal malfunctions. You can troubleshoot the issue more skillfully if you are aware of the potential causes.

This post will discuss some of the typical causes of a Siemens washing machine not turning on as well as offer workable solutions.

Possible Cause Solution
Power supply issue Check if the washing machine is plugged in and the outlet is working.
Door not closed properly Ensure the door is fully closed; the machine won"t start if it"s open.
Control panel malfunction Try resetting the machine by unplugging it for a few minutes.
Blown fuse or tripped circuit breaker Check your home"s fuse box and replace or reset as needed.
Faulty power cord Inspect the power cord for damage and replace if necessary.

The most likely malfunctions

It makes sense that a dead dashboard would indicate a power supply issue. Put simply, the system cannot start and the washing machine does not receive power. There are multiple reasons why Siemens might act in this manner:

  • there is no electricity in the room;
  • the electricity supplied to the equipment is unstable, the voltage reaches critically low or high values;
  • the socket supplying the Siemens is broken or de-energized;
  • the network cable is damaged (the plug is melted, the insulation is damaged);
  • the line filter (NPF) is knocked out;
  • there are problems with the "Start" button (burned out or stuck);
  • the control board is out of order.

The power supply may be malfunctioning if the Siemens washing machine won’t turn on.

The electronics and electrics must be inspected in order to get the equipment operating again. There was most likely a circuit break, either inside or outside the Siemens. The steps to follow are very straightforward: check each potential failure one after the other. It is preferable to begin with something straightforward, like the central power supply.

Power grid

The most common cause of power outages is simply that there isn’t any light in the room or apartment. particularly if the washing machine is located in an isolated area or the country, where power outages are common. As a result, we turn on the light and see if the room is powered on initially.

If there is no light, examine the panel to see if the plugs are burned out or if the machines are turned on. The residual current device (RCD) may have been activated by an overload; as a result, the line was automatically de-energized for safety. Recalculating the voltage used by home appliances and adjusting the network load by temporarily turning off multiple devices are preferable options.

The socket’s serviceability must be examined next. The indications listed below will point to issues with the point:

  • smoke;
  • burning smell;
  • melted plastic;
  • Dark spots around the outlet.

We check the socket internally after making sure it is intact on the outside. Plugging in a functional device, such as a hair dryer or phone charger, is sufficient. Is there communication? Then there was another breakdown.

As soon as you notice dark areas, melting, burning smells, or fire, you need to turn off the power and call an electrician!

Fixing a malfunctioning socket and modifying the load applied to it are necessary. Excluding the possibility of a recurrent short circuit requires stopping the use of excessively powerful devices and securing the terminals. Although replacing the electrical outlet by hand is not difficult, it is best to contact a specialist if you lack experience.

FPS

You will need to perform an internal diagnostic on the washing machine if there are no issues with the Siemens power supply externally. The electrical board, the interference filter, and the power cord are the three components we are discussing. We examine the first two first. Since the cord and FPS on Siemens washing machines are connected, they are checked right away. We work in this manner:

  • disconnect the equipment from communications (sewage, water supply and power supply);
  • turn the Siemens with the back panel forward;
  • unscrew the top cover of the machine;
  • find the capacitor located in the lower left corner at the back wall;
  • loosen the bolts holding the FPS;
  • pull the filter freed from the fasteners out of the case together with the power cord.

Check the plug first for any signs of melting or fire. After that, connect the multimeter probes to the cord in buzzer mode to check for breakdowns. The most important step is to short the sensors together in order to test the device directly. It is operational if the number "0" shows up on the display.

Keep safety in mind when inspecting electronics! Avoid touching live wires!

It is necessary to replace a damaged cord with a new one. It is not acceptable to try to fix it yourself by twisting or using electrical tape since this is dangerous. The likelihood of recurrent current leakage followed by a fire or short circuit is very high. Next, we use a multimeter in buzzer mode to test the interference filter. Additionally, we measure the resistance right away. Should the figure on the screen deviate significantly from the expected value, the capacitor has burned out. The replacement process is straightforward: we purchase a new FPS and install it in place of the old one, paying attention to the Siemens serial number.

It can be annoying if your Siemens washing machine won’t turn on, but there are steps you can take to figure out why. Start with the essentials, such as making sure the door is closed correctly and inspecting the power supply. Often, the issue can be swiftly resolved with these easy checks.

Should the device remain unresponsive, a more significant problem such as a malfunctioning power cable, a blown fuse, or an issue with the control board may exist. In order to prevent more harm from occurring, it might be time to speak with a qualified technician at this point.

Recall that maintaining your washing machine in good operating order requires routine maintenance and prompt repairs. Early resolution of minor issues can avert larger ones later on.

Simple problems like a loose power connection or more complicated issues with the internal components could be the cause of your Siemens washing machine’s inability to turn on. Before you hire a pro, this post will walk you through typical causes of this problem and doable actions you can take to troubleshoot and possibly resolve the issue yourself.

Video on the topic

Siemens IQ300 washing machine problem: unstable operation of the lock, door, start button. (solution)

Repair of the BOSCH, SIMENS electronic module

Siemens iQ500 (WS12M441OE) does not turn on

Siemens dryer does not turn on / simple repair

MiKaService| Siemens washing machine does not turn on

SIEMENS washing machine. How to reset the error? Also – view the last error and turn on/off child protection

How to enter test mode in a Siemens XLM 128 washing machine

Reset Siemens. Siemens washing machine reset. How to remove a Siemens washing machine error

How often do you conduct maintenance of your washing machine (cleaning filters, drum, and t.d.)?
Share to friends
Ekaterina Vasilieva

Consultant on choosing household appliances. Working in a hardware store, I helped many customers choose washing machines that perfectly suited their needs. In my articles, I share recommendations and personal life hacks for choosing and using, so that it is easier for you to make a decision.

Rate author
FAQ-Washer.com
Add a comment