Indesit washing machine constantly collects water

You’re not alone if your Indesit washing machine appears to be stuck in a never-ending cycle of filling with water. This annoying problem, which can interfere with laundry schedules and raise questions about water waste or possible damage, has been experienced by many users. You can avoid more issues and save time by knowing why this occurs and how to handle it.

The water inlet valve, which regulates the flow of water into the machine, is frequently the source of this issue. Occasionally, a broken valve may not shut completely, allowing water to keep entering the drum. At times, an obstruction in the system or an issue with the water level sensor may be the cause of improper drainage.

It helps to thoroughly inspect these parts in order to identify the root of the problem. You can maintain the optimal functioning condition of your washing machine with routine maintenance and fast troubleshooting. Let’s examine some typical reasons and workable fixes to assist you in properly resolving the issue.

"Symptoms" of breakdown

Typically, the automatic machine fills and drains water multiple times (two to three times) while washing. It is hard to ignore the constant inflow of liquid into the system. The primary "symptoms" that users have identified in this case are:

• incessant noise of water being collected;
• extended washing program. Since the process is carried out incorrectly, the cycle time increases;
• at the end of the wash, the clothes are still dirty, with soap stains. This is observed because the required concentration of the soap solution is not achieved.

As soon as the issue is identified, the cause of the machine continuously filling with water must be removed.

Operating the washing machine in such a manner is risky. This carries the risk of the equipment breaking down entirely.

What could have failed?

There are a number of reasons why the Indesit machine keeps filling with water. First, every potential issue must be found, and then the diagnostic process’s scope of malfunctions must be limited. Thus, as a result of what, a constant accumulation of liquid from the water supply is seen:

• incorrect connection of the washing machine;
• damaged washing machine tank;
• failed pressure switch;
• broken inlet solenoid valve;
• faulty control module.

It’s not a guarantee that the machine is connected incorrectly if the only issue it had was with the first wash after purchase. Maybe there’s a typical manufacturing flaw. In this instance, it is preferable to give the equipment to a service center for warranty service rather than attempting the repair yourself.

Let"s check the drain hose

Simple to complex diagnostics should be performed on the Indesit washing machine. It is advisable to first examine the machine’s connection. The most common reason why Indesit washing machines keep collecting water is a misconnected drain hose.

Every piece of equipment has detailed instructions that walk you through connecting it to your home’s utilities. The primary guideline is to position the drain hose between 50 and 60 centimeters above the ground. Lowering the hose will cause the water to fall through the pipe due to gravity. The pressure switch will then notify the "brain" that the tank is empty, and the control center will then issue an order to refill the system with water. And the circle goes on.

You can visually determine whether this is the cause by looking at the hose and ensuring that it is at an appropriate height. In the event that an inspection is not feasible, the hose’s position may be assessed in an alternative manner.

• turn on any washing program;
• wait until the tank is full;
• start the "Drain" mode;
• press the "Pause" button in the middle of the descent.

The drain hose is unquestionably the source of the issue if the liquid keeps leaving the system even after the process is stopped. You will need to investigate the issue further if the water level doesn’t change.

In addition, the equipment frequently comes with a unique loop that is meant to fix the drain sleeve. The hose is fixed in the proper location when it is inserted into the plastic element.

Problems with the inlet valve

An inlet valve failure may be the cause of continuous water intake in certain situations. A malfunctioning sensor causes liquid to continuously enter the system. Thus, the "brain" commands to fill the tank when the wash begins. Water intake cannot be stopped by a broken valve. When there is too much liquid, the protective mechanism kicks in and starts to drain it. The procedure is circular in nature. In this situation, what ought the housewife to do?

You ought to be mindful of:

• the speed of filling the tank. If the water enters slowly, the valve membrane is probably damaged;
• too fast filling indicates a breakdown of the electromagnetic element itself.

It is not possible to fix the inlet valve; a new component must be purchased and installed.

The following steps will be taken in order to disassemble the element and then install it:

• de-energize the washing equipment;
• remove the top cover from front-loading machines, or the side cover for vertical-loading machines;
• find the inlet valve, disconnect all wiring and pipes from it;
• unscrew the bolts holding the valve or loosen the locking latches (depending on the type of fastening of the element on your model of washing machine);
• remove do;
• put a new valve in place, tighten the bolts (or secure it with latches), connect the pipes and wires;
• assemble the washing machine body;
• run a test wash.

You can perform this task at home with ease; changing the valve is not hard. Choosing a replacement part that is comparable to the one being disassembled is crucial.

The level sensor is malfunctioning

The water volume in the system is tracked by the pressure switch. The sensor notifies the control module and the "brain" tells it to stop filling the tank when the tank reaches the necessary level. The control unit won’t get accurate information about the volume of liquid in the tank if the pressure switch malfunctions. This throws off the regular washing cycle. There are several reasons why the level sensor may stop working properly.

• oxidation of its connectors and contacts;
• short circuit in the pressure switch wiring;
• loss of membrane tightness;
• clogging or defect of the pressure tube.

Initially, you could attempt to fix the sensor by cleaning the oxidized contacts, welding the flaws, and removing the obstructions. Should this fail to yield an outcome, you will need to purchase and install a functional press-start. The following will be the sequence of events:

• Remove the “top” of the machine body by unscrewing the bolts holding the lid;
• Disconnect the pressure tube from the level sensor;
• turn off the chip with wiring;
• Eliminate the press -start, unraveling the latch fixing it;
• Put a working element;
• Connection in the reverse order (chip, tube);
• Fasten the top cover of the washer in place.

When performing repairs on a locomotive machine, make sure you follow safety protocols by turning off the equipment’s network connection and closing the shut-off valve.

It is also crucial in this case to select a part that is comparable to the one that was removed. After determining the Model Assistant model’s precise name, buy a replacement detail.

There are a few common reasons why your Indesit washing machine might be collecting water all the time. This annoying scenario can be caused by issues such as a broken water inlet valve, a blocked filter, or a malfunctioning drain pump. You can diagnose and resolve the problem, ensuring your washer operates smoothly and efficiently, by being aware of how these parts function and doing regular checks on them.

Damage to the main container

The Indesit washing machine’s tank crack is far from uncommon. Water will collect under the washing machine during washing, making it simple to identify a puncture. This malfunction poses a serious risk since it could result in flooding within the apartment, harming not only your house but also your neighbors’ properties.

The tank’s bottom has the most hazardous cracks. Although most Indesit programs only call for partially filling the drum with water, hole holes in the upper part are not as bad because in this scenario the water will not flow out onto the floor. To examine the tank’s bottom:

• de-energize the washing machine, disconnect the inlet and drain hoses from the communication outlets;
• drain the water from the tank (through a garbage filter or drain hose);
• pull the machine out to the middle of the room (the ideal place for repairs will be the garage);
• lay the washing machine on its right side;
• inspect the bottom of the tank. You can use a marker to mark suspicious places that look like holes.

It is best to replace a leaking SMA tank with a new one. Nevertheless, if the flaw is not too big, you can attempt to use cold welding or a high-temperature, waterproof sealant to repair the element’s integrity. You can ask a specialist to solder the tank if you take the equipment to a repair shop. You should be aware, though, that obtaining a guarantee for this kind of repair will be challenging.

It’s important to fix your Indesit washing machine’s water collection issue as soon as possible. There are several possible causes of this problem, including problems with the drain pump, a broken pressure switch, or a malfunctioning water inlet valve. Finding the source of the problem is essential to solving it successfully.

To begin fixing the problem, make sure the water inlet valve isn’t damaged or clogged. Check the pressure switch as well for any indications of a malfunction. Check the drain pump for damage or blockages if all other parts appear to be in working order. These issues can be avoided by timely repairs and routine maintenance.

In the end, taking quick action to resolve water collection problems will guarantee that your washing machine works effectively and lasts longer. It can save you time and potential headaches to consult a professional if you’re unsure about DIY repairs or uncomfortable doing them yourself. Maintaining the condition of your washing machine can help you steer clear of more serious problems later on.

Video on the topic

Water overflow in the washing machine. Causes and do-it-yourself repair

Indesit washing machine, Indesit pump is constantly running

Water overflow REPAIR INDESITT WISL105 HOW TO REPAIR WATER OVERFLOW IN 30 MINUTES IN A WASHING MACHINE

The washing machine is constantly filling with water. How is this related to the transport bolts?

The Indesit washing machine is constantly filling with water

The washing machine is constantly filling with water

The Indesit WIE107 washing machine is constantly filling with water.