How to replace bearings on a Vestel washing machine

Although replacing the bearings on a Vestel washing machine may seem difficult, you can do it yourself if you take the proper approach. Your washing machine’s bearings may eventually wear out and stop working properly, making loud noises during the spin cycle.

Think about repairing the washing machine yourself before you run out and buy a new one. You can save money and prolong the life of your appliance by replacing the bearings. We’ll walk you through the procedure step-by-step in this post, so you’ll know exactly what to do and what equipment you’ll need.

This guide will assist you in getting your Vestel washing machine operating properly once more, regardless of whether you’re a do-it-yourself enthusiast or just trying to avoid expensive repairs. Let’s get started and make this a wash day that is more productive and quiet.

Let"s collect everything you need

A Vestel machine’s bearing replacement requires some preparation beforehand. First, we discover a hammer or puller, flat and Phillips screwdrivers, pliers, side cutters, a screwdriver, a rubber mallet, a set of wrenches, and Allen keys. You’ll also want a couple of fresh rags.

Apart from the tools, you will also require new replacement parts. Visit the market, a repair facility, a specialty shop, or place an online order to accomplish this. In any event, it is preferable to pay attention to the model’s serial number, which needs to be displayed on the marking sticker on the machine’s rear. It is advised to replace both seals in addition to the bearings, and calipers for top-loading machines should be purchased as part of the kit. Having kerosene, universal WD-40, or grease for seals on hand is also essential.

Crucial! Take out the damaged model and pay attention to the markings on it so that you don’t make any mistakes regarding the size of the bearing and seal.

Next, get the washing machine ready for maintenance:

• disconnect the unit from the power supply;
• turn off the water supply and disconnect the inlet hose;
• unscrew the drain hose;
• for convenience, twist all the hoses and cords;
• move the equipment away from the wall or take it out of the cabinet to such a distance that you can freely approach the back wall.

One more piece of advice: don’t be too lazy to prepare a notebook and a camera beforehand. Reassembling the machine can be facilitated and many errors can be avoided by carefully documenting every step of the disassembly process. After everything is put together, start the disassembly process.

Preparatory stage

Although replacing the bearing assembly by hand is very challenging, it is doable with extreme caution and no experimenting. When in doubt, it is best to get in touch with qualified repairmen to avoid making the issue worse and necessitating a significant overhaul. As a result, before beginning any work, carefully read the instructions and gauge its level of complexity.

1. First, check the condition of the bearings again. Spin the drum and listen. If there is a cracking, knocking and a quick stop – begin disassembly.
2. Go behind the machine and unscrew the two bolts holding the top cover. Then we return to the front side and gently move the top away from you. Once the latches are released, you need to remove the cover and put it aside.

Note: To keep all the small parts and fasteners from getting lost, flip the removed cover over and use it as a stand.

1. Tilt the case back a little.
2. Pull out the external dispenser by pulling it sharply towards you.
3. Unscrew the bolts holding the front panel on both sides of the case, as well as the fasteners on the powder receptacle.
4. Move the removed panel to the side.
5. Move to the hatch cuff. Remove the front clamp and tuck the rubber inside.
6. Remove the front bar. Unscrew the four screws, one in each corner, close the door, lower the panel down until the latches engage, move the door lock and remove the part.
7. Remove the second part of the bar by unscrewing two screws on both sides.
8. Select suitable heads and unscrew the counterweights from the bottom and top.
9. Disconnect the remaining part of the dispenser by removing the valve and pulling out the pipe.
10. Use pliers to release the clamp on the lower pipe.
11. Loosen all the clamps on the existing wires.
12. Release the wiring.
13. Use your hands to pull out the shock absorbers and disconnect the pressure switch.

The setup phase is complete. The tank only needs to be removed, which can be done by holding it in one hand and taking out the springs on either side with the other. Next, set the plastic container with the crosspiece facing upwards on a cushioned surface and start taking the bearing unit apart.

Vestel washing machine bearing replacement isn’t as difficult as it might seem. You can prolong the life of your appliance without having to hire a professional if you have the right tools and a little perseverance.

From taking out the drum to installing the new bearings, don’t forget to carefully follow the instructions. You will feel accomplished after fixing your washing machine yourself, in addition to saving money.

Don’t be afraid to ask for assistance or consult more guides if you encounter any problems or have questions at any time. The most crucial things to consider are your safety and the machine’s correct operation.

Although replacing the bearings on a Vestel washing machine may seem difficult, you can do it yourself if you have the right equipment and follow the instructions step-by-step. This post will simplify the procedure into doable steps so you can prolong the life of your machine and reduce repair costs.

Video on the topic

Vestel. Replacing the bearing 3 minutes

Vestel. Vestel replacing bearings. Washing machine review.

Repair of the VESTEL washing machine.

Vestel replacing bearings. How to disassemble and assemble a washing machine.

Replacing the bearing in a washing machine Vestel

Vestel. Vestel bearing replacement. Washing machine review.

How to replace bearings on a VESTEL washing machine