Here is a succinct overview of your piece:
The bearing in your Atlanta washing machine may be the cause of strange noises or improper spinning. Although changing a bearing might seem difficult, you can do it yourself if you have the right equipment and a little perseverance.
We’ll walk you through replacing the bearing in your Atlanta washing machine step-by-step in this article. Everything from figuring out the issue to carefully taking the machine apart and putting the new part in will be covered.
You can prolong the life of your washing machine and reduce the cost of repairs by following these instructions.
Step | Description |
1 | Unplug the washing machine and remove the back panel. |
2 | Detach the drive belt and disconnect the motor. |
3 | Unscrew the drum and carefully take it out. |
4 | Remove the old bearing using a bearing puller or similar tool. |
5 | Install the new bearing and ensure it is securely in place. |
6 | Reassemble the machine by following the steps in reverse order. |
7 | Test the machine to ensure it operates smoothly. |
Although it may seem difficult, changing the bearing in an Atlanta washing machine is a task that can be completed at home with the correct equipment and assistance. This post will walk you through the process of determining whether your machine is experiencing bearing wear, how to safely remove the old bearing, and how to install a new one so that it functions properly once more.
- How to disassemble an Atlant washing machine
- Change the bearing on the Atlant washing machine
- Assembly of the washing machine Atlant
- Video on the topic
- Replacing bearings in the Atlant washing machine.
- Replacing bearings and a half-tank in the Atlant washing machine.
- I KNOW HOW to change a bearing on an Atlant washing machine
- Replacing bearings in the Atlant washing machine
How to disassemble an Atlant washing machine
Common screwdrivers, socket heads, and a few other tools are all you’ll need to disassemble an Atlant washing machine.
Buying a new set of bearings and an oil seal beforehand will help to expedite the entire procedure.
You can buy the required parts in specialized shops or services by simply providing the brand and model of your product to the seller. You should not cut corners when purchasing new parts because you are already cutting corners when doing do-it-yourself fixes, and using parts of questionable provenance will soon have you repeating this process.
Washing machine bearings are subjected to extreme loads, so production is given particular consideration when determining their quality.
Disconnecting the device from the outlet and other communications is the first step in any repair:
- Unscrew the top cover of the product and remove it from the body, moving it away from you a couple of centimeters (it is fastened with 2 screws in the rear end part of the cover);
- Remove the powder tray and unscrew the hopper mounting screws underneath it;
- Next, dismantle the upper front panel;
- Unscrew and remove the spacer metal crossbars;
- Remove the electronic control unit from the inside of the body on the right, first disconnecting the thin hose from it;
- Remove the upper concrete weight;
- Disconnect the tray hopper from the hoses and remove it outside;
- Remove the outer clamp of the hatch cuff and tuck the rubber inside the machine body;
- Remove the back cover of the washing machine body;
- Disconnect the wires from the heating element and temperature sensor, rewrite the correctness for subsequent connection (it is better to take a photo);
- Unscrew the motor mounting bolts and remove it from the hinges;
- Loosen the hose mounting clamp on the tank (hose to the pump);
- The shock absorbers can be unscrewed from both the tank and the body, but you can leave them alone (their rods will come out of the bodies themselves).
We now remove the tank vertically upward, making sure it only makes contact with the washing machine body through the use of springs. To make things easier, open the hatch. The second concrete weight in the tank needs to be removed in order to replace the bearing on the Atlant washing machine.
Change the bearing on the Atlant washing machine
The collapsible design of the tank in Atlant washing machines facilitates maintenance tasks such as replacing the hub’s bearing. You have to loosen about twenty bolts around the edge of it in order to split it in half.
Then just unscrew the tank’s two halves and set the front one aside. From there, we’ll take the following steps to deal with the hub bearing-equipped rear portion of the tank:
- Unscrew the bolt securing the drum pulley and remove the wheel by shaking it;
- In place of the bolt, screw in a similar one, and knock the drum shaft out of the bearings with hammer blows. After removing the drum from the tank, pay attention to the condition of its shaft and the brass bushing on it. The bushing should have a smooth, even surface, if the surface of the part is damaged, it or the entire drum cross must be replaced;
- Then, using a minus screwdriver, remove the oil seal from the hub;
- Using a hammer and chisel (or a piece of thick-walled metal pipe), knock out the old worn bearings from the hub. They need to be knocked out by hitting them crosswise around the circumference of the inner race of the part, having previously lubricated the hub to facilitate the release of the bearing from the tank;
- Afterwards, it is necessary to clean the hub and the places where the halves of the tank are connected from foreign deposits and dirt.
The tank hub needs to be cleaned and lubricated before new parts are installed.
Bearings 6204 and 6205 with a 30*52*10 seal or bearings 6203 and 6204 with a 25*47*10 seal are typically found in Atlant washing machines.
The Atlant washing machine’s bearing size is determined by its number; for instance, the outer diameter of the 6203, 6206, and 6205 are 40, 47, and 52 mm, respectively.
- We take the smaller bearing and install it as evenly as possible by hand, then gradually press it in with a hammer along the outer race in a circle until it stops on its seat;
- Then we install the large bearing in the same way, we seat it completely using a piece of pipe or a chisel;
- We put a special water-repellent grease (you can use Litol-24) into the oil seal and put it in its place, usually with hand pressure it reaches the installation site;
- Then you need to carefully insert the drum with the shaft into the bearing assembly, install the pulley on the back side and secure it with a bolt;
- The joints of the halves of the tank must be treated with a sealant and connected with bolts. The sealant must be chosen given that he will need to withstand the high temperature and the aggressive environment (alkali, acid, etc. D.).
Assembly of the washing machine Atlant
Put the washing machine back together in the opposite order. However, the shock absorber rods should be hung on the springs after being inserted into their housings during tank installation. As you refer to your notes or photos, connect the wiring.
It is best to take pictures of the entire disassembly procedure as this will guarantee that the unit is assembled correctly afterward.
You may have to pay more for replacement parts if the assembly is flawed, particularly if the wires are connected improperly.
Once the product is assembled, it must be left undisturbed for the duration of time specified by the sealant manufacturer to ensure full hardening. After that, test-wash the device with a small quantity of detergent and reconnect it to all communications.
This is done to get rid of any potential dirt in the machine and any bad smells that came from the sealant drying.
The Atlant washing machine’s DIY bearing replacement was completed to the correct standard if, following the test wash, there are no signs of moisture underneath the machine and the program operates at a noise level that is acceptable.
Although changing the bearing in an Atlanta washing machine may seem difficult, many do-it-yourselfers can complete the task successfully with the correct equipment and advice. Your washing machine’s lifespan can be increased by carefully following each step and taking your time to ensure a successful repair.
Prioritize safety above all else by unplugging the computer and setting up your workspace before starting the replacement procedure. Approaching the task methodically will help you avoid errors and simplify it.
You’ll feel more accomplished and be able to save money by doing the repair yourself. Your Atlanta washing machine will soon be operating smoothly again if you are patient and pay close attention to details.