How to change the seal in the Indesit washing machine

Although it may seem like a difficult task, changing the seal in your Indesit washing machine is actually much easier than you might think. Leaks and water damage can result from the seal surrounding your washing machine door wearing out or becoming damaged over time. You can replace it with the help of this guide, which will guarantee that your machine operates smoothly and effectively.

We’ll go over the main reasons why replacing the seal is necessary first. During washing, the door seal, also known as the door gasket, keeps water inside the drum. It can leak when it gets worn out or damaged, which could result in more serious problems if it isn’t fixed right away. Not only will replacing the seal stop leaks, it will also keep your washing machine operating at peak efficiency.

We’ll then go over the equipment and supplies you’ll need for the task. Just a few standard tools and a new seal that fits your Indesit model will do; nothing too fancy. We will also give you advice on where to look for the proper seal and how to make sure the part you buy is the right one for your particular machine.

Lastly, we’ll walk you through the precise steps of changing the seal. We’ll simplify it into simple instructions so you can do it yourself without consulting an expert. By the time it’s all over, your washing machine will be like new and ready to handle your laundry without any leaks.

Dismantle the tank together with the drum

It is inconvenient, but you will need to disassemble the device nearly entirely in order to alter such crucial components. However, take your time disassembling the device by hand. Before you do so, disconnect the electricity and water supply, and then move the device to a roomy space where you can work comfortably. You will need to have a hammer, WD-40 aerosol, and a screwdriver ready in order to disassemble the equipment. Once everything is ready, you can begin changing the parts.

• We remove the top cover of the washing machine, for which it is necessary to remove the fixing screws, which are located at the back on the lugs.
• Remove the tray for household chemicals by gently pulling it by the handle.
• Having loosened the screws located around the perimeter, we remove the instrument panel of the machine.
• Using a screwdriver, you need to pry and remove the false panel located at the bottom right of the washing machine.
• We open the hatch, inside which you should loosen the outer clamp on the cuff, for which you need to carefully pry the clamp with a screwdriver.
• Now you need to tuck the cuff into the drum.
• Carefully disconnect the wiring of the hatch locking device.

To have a reference later on for correct wiring connections, make sure to take multiple pictures of the wires connected correctly.

• We remove the bolts that hold the front panel of the equipment, and then remove the panel.

This is how we will grant unrestricted access to the washing machine’s tank and drum in eight locations. But, until you have disconnected the pipes and wires that are attached to the containers, you shouldn’t take any more actions or take the containers out of the case. What comes next?

• First of all, dismantle the filling pipe.
• Next, disconnect the pipes that go directly to the household chemicals tray.
• Remove the metal false panel located at the back of the washing machine body.
• Lower the counterweights by loosening the central bolts.
• Disconnect the thermistor, having previously removed the wires from the connector.
• Disconnect the wires of the water heating element, and then pull out the heating element itself.

Now that the wiring has been resolved, the tank needs to be ready for operation. Since the front of the washing machine is already freely accessible, all that’s left to do is ready the back by removing the drive belt and loosening the pulley. The guidelines are as follows:

• unscrew all five screws that secure the back panel of the washing machine;
• remove the belt from the pulley;
• loosen the nut that holds the pulley;
• remove the drum of the machine.

Once you have the drum in your hands, you can assess the crosspiece’s state. Examine the shaft; if it shows no signs of wear, abrasion, or chipping, the element is operating as intended. In this instance, you should start working with the bearings and leave the part alone. You will need to either buy a new unit or restore the blades if there are issues with the shaft.

You can’t do without cutting the tank

Regretfully, Indesit’s "home helper" tanks are irreversibly broken down. Representatives of the company think that if the bearings are damaged, the equipment owner will either purchase a brand-new washing machine or a completely new tank with a drum. Naturally, it is far less expensive to just replace the bearings, so you will need to carefully saw the tank yourself, replace the parts, and then put the tank back together.

Your chances of success are higher if you have an electric jigsaw. Unfortunately, not everyone has one of these tools at home, so the majority of people use a metal hacksaw to work on the tank at home. Most people own this simple, low-cost instrument, but the drawback of using one of these hacksaws is their slow speed—it will take you several hours or longer to split a tank in half. This is totally inappropriate for routine repairs at a service center, but it is acceptable for one-time fixes on your own home appliances.

With a Gross wood saw, which stands out for having small, hardened teeth that allow it to easily handle a washing machine’s tank, the task will be completed much more quickly.

In addition, you will require two washers, a hacksaw blade, and a bearing for a four bolt if you choose to purchase an ordinary jigsaw in order to expedite the process. The latter is required because an electric jigsaw’s standard blade is too wide; it will be much more practical to modify a thin blade from a standard hand jigsaw. In order for the tip of such a blade to be properly connected to the electrical device, it must first be shaped like a jigsaw blade.

Once the blade has taken on a form suitable for inserting into an electric jigsaw, fasten the entire assembly using bolts, washers, and bearings. To accomplish this, put the bearing in the center, install the washers on the sides, and tighten everything with a bolt.

Start sawing the tank as soon as the tool is ready. Although a standard jigsaw blade can be used for this, adapting the blade to fit a jigsaw will be much more convenient and expeditious.

Sawing has few subtleties. The most crucial step is to carefully and as smoothly as possible saw along the seam. The easier it will be to glue the tank back together, the smoother the division into two halves.

An easy fix that can stop leaks and boost your machine’s performance is changing the seal on an Indesit washing machine. You may maintain the smooth operation of your washing machine and save expensive repairs by taking a few easy precautions: taking out the old seal, cleaning the new one, and carefully installing it. Your machine will remain in optimal condition because this guide will take you step-by-step through the entire process, making it simple and hassle-free.

Changing the parts with your own hands

Now, let’s get to the important part: taking out the bearings. All you need for this crucial stage of repair is a regular hammer and a specialty punch. Starting to work.

• Remove the oil seal.
• Place the end of the punch in the very center of the rear bearing and start tapping the metal rod with a hammer.

Always alter the direction of the rod when striking a spot.

• After finishing work with the first bearing, proceed to extract the second bearing.

For the sake of making bearing disassembly easier, it is acceptable to carefully saw and chip the part if the inner race flew out but the outer one stayed in place.

After working on the bearings, spend some time cleaning the machine to remove any remaining dirt, rust, scale, and debris. The drum shaft needs to be cleaned as well. After cleaning is complete, you can move on to seal installation, seat lubrication, and bearing preparation.

The Indesit washing machine’s seal measures 22 by 40 by 10 millimeters. Remember that you must purchase two of these parts for the washing machine at the same time. In terms of the bearings, the first one should ideally be type 6203 closed type 2RS, and the second one should be type 6202, also type 2RS. Remove the damaged seals with bearings first, then take them to the store as an example, so that you can precisely purchase the correct part.

After buying new components, you must install the grease-pretreated bearing in the designated socket. Using the same hammer and a metal rod, carefully tap the bearing on the outer race. On the seat, the bearing needs to rest equally. The identical scheme is followed when installing the second bearing. The seals need to be installed on top of the bearings and lubricated afterwards.

Although it may seem difficult, changing the seal in your Indesit washing machine is definitely doable with the right tools and a little patience. The seal, also known as the door gasket, is essential to stopping leaks and maintaining the optimal operation of your washing machine. You can avoid future, more expensive repairs by performing routine maintenance and replacing worn parts on time.

Turn off the water supply and unplug your washing machine from the power source first. This guarantees your security as you work. Depending on the model of your machine, removing the old seal requires removing the front panel or door. After removing the old seal, make sure the area is completely clean to get rid of any debris or residue that could make it difficult for the new seal to fit correctly.

Make sure the new seal is correctly positioned and free of folds or twists before installing it. It should cinch tightly around the opening of the door. Reassemble the door or front panel after the new seal has been installed, then turn on the water and power supplies again. To make sure everything is operating smoothly and there are no leaks, test the machine with a small load of laundry.

You can maintain your washing machine’s optimal performance and lifespan by adhering to these steps. Frequent maintenance inspections can help you identify problems early and streamline your laundry routine.

Video on the topic

how to change the cuff on Indesit

Replacing bearings of an Indesit washing machine in an original way

Replacing bearings and a seal in an Indesit washing machine | Repair of washing machines in Kaluga