It’s usually an indication that the heating element in your Beko washing machine has worn out when the water no longer heats up correctly. Your machine’s heating element, which can burn out or sustain damage over time, is what warms the water for effective cleaning. Fortunately, replacing it isn’t as hard as you might imagine.
You can repair your washing machine with a few simple tools and some perseverance. We’ll walk you through changing the heating element on your own using this guide, which will spare you the expense of a service call.
It’s crucial to understand how to access the heating element, remove it safely, and install the new one before you begin. This is an easy process to do on your own, whether you’re handy with repairs or just want to save money on a costly technician visit.
If you know where to look and how to handle the replacement safely, changing the heating element in a Beko washing machine can be a straightforward procedure. The machine must first be unplugged from the power source, the back panel must be removed, and the heating element must be found close to the drum’s bottom. When the new element is located, carefully unplug the wires, remove the old one, and screw it in place. Before reassembling the machine, make sure everything is secure. This easy fix will get your washer operating again while saving you the expense of hiring a technician.
- Let"s prepare everything you need
- Looking for a heater in the case
- We repair the machine ourselves
- Video on the topic
- Repair of Beko washing machines. DIY heating element replacement.
- Replacing the heating element of a Beko washing machine. Beko washing machine does not heat water
- BEKO DOES NOT HEAT WATER. WASHING MACHINE CONTROL MODULE REPAIR MACHINES.
- How to replace a heating element on a washing machine in 10 minutes
- How to change the heating element on a Samsung, LG and other washing machines / Replacing the heating element on a washing machine
- How to remove the heating element on a washing machine
- How to replace the heating element in an LG, Samsung and other washing machines
Let"s prepare everything you need
A defective heating element is almost easy to disassemble and replace with a new one by hand. Furthermore, a typical home "set" will do; special tools and equipment are not required. To be more specific, you will need an 8-mm head ratchet, a multimeter, a Phillips and slotted screwdriver, and any technical lubricant that is readily available for the repair.
The process of choosing a replacement heater is no longer difficult. An equivalent of the damaged heating element is available online, at a service center, and at the closest hardware store. A heating element typically costs between eight and ten dollars.
Selecting the ideal heater is the primary task. Every washing machine model has a specific kind of heating element installed, and if the new device is too big or too powerful, it will break down too soon. To avoid making a mistake on the purchase, you have to:
- copy the marking from the old heating element, which is applied to the surface of the spiral;
- dismantle the device and bring it to the store as a sample;
- focus on the serial number of the existing Beko.
A new heating element typically costs $10.
Either way, it is imperative to ascertain the precise amount of heating element power needed. Typically, 1850 W indicator devices are bought for Beko washing machines. All machines are unique, though, and some are capable of operating at higher values.
Looking for a heater in the case
The tubular electric heater in Beko washing machines is situated beneath the tank, which is a typical location for machines. Disconnecting the equipment from the water supply and network, unfolding the case, removing the drive belt, and removing the back panel will make it simple to reach the heating element. Right beneath the drum’s base lies the intended component – a circular metal "plate" with numerous interconnected wires.
Since the heating element is always encircled by wiring and located beneath the tank, it is impractical to mistake it for the engine or another component of the washing machine. When you take the machine apart, the first thing that catches your eye is this.
Finding the source of the breakdown is frequently the problem, even if replacing the heater is not too difficult. Many issues can cause the heating element to fail, so it’s best to perform a thorough diagnostic on the machine before starting any work. Generally speaking, "thermal failures" are caused by the following issues:
- sharp voltage surges in the network;
- incorrect operation of the heating element temperature sensor;
- overheating of the device due to a thick layer of scale (if the water in the water supply is dirty or too hard);
- water getting on the contacts;
- human inattention or error;
- factory defect.
Voltage surges cause the heating element to burn out most frequently.
Replacing a malfunctioning heating element will usually resolve the issue. If the control board is "to blame," it gets worse. A module that malfunctions, possibly because of broken "tracks" or loose connections, needs to be fixed individually. It is safer to contact a service center rather than attempt to repair the electronic unit yourself, though.
We repair the machine ourselves
A malfunctioning heating element prevents you from using the machine. Initially, upon activation, the self-diagnostic mechanism will commence, manifesting a signal regarding the malfunction either via the LED indicator or the display. Secondly, stains cannot be eliminated by using cold water when washing. It is preferable to begin repairs right away rather than wait.
Here are detailed instructions for replacing your home’s heating element. Prior to anything else, make sure the washing machine is not still connected to the power. Subsequently, the water supply and sewage are cut off. Draining the unit’s remaining water will be the third step because, in the event of further repairs, waste liquid may seep out and get on the contacts.
The garbage filter is used to drain the water:
- hook the technical hatch with a screwdriver and remove it;
- prepare rags and oilcloth;
- place a container for collecting water under the filter;
- unscrew the trash filter, acting clockwise;
- collect dirty water.
After being emptied, the machine is rotated and partially dismantled. The drive belt is removed after the back wall has been removed and the retaining bolts have been unscrewed. We start the diagnostic process as soon as the heater is free to access:
- look for the heating element under the tank;
- disconnect the wiring from the "chip";
- set the multimeter to the "Resistance" mode;
- apply the tester probes to the heater contacts;
- evaluate the displayed value – normally the resistance should fluctuate within 20-30 Ohms.
It’s time to replace the multimeter if the reading deviates from the average. To accomplish this, simply take apart the old heater by unscrewing the center bolt, pushing the fastener inward, using a screwdriver to pry open the heating element’s base, and removing the unit. Because the tightness is caused by a damaged rubber seal, it is crucial to proceed with extreme caution.
A ripped rubber will start to leak water when the heating element is disassembled, breaking the seal.Take care not to damage the seal.
Make sure the seat is completely clean after removing the heating element. After that, insert the device into the groove, tighten the nut on the heating element bolt, and grease the rubber gasket. Attach the wiring at "finish".
After the repair is finished, examine the caliber of the work that was done. After 20 minutes of starting, place your palm against the hatch door and begin a "idle" wash with water heated to between 50 and 90 degrees. The heater replacement was successful if the glass is hot.
| Step | Description |
| 1 | Unplug the washing machine from the power source. |
| 2 | Remove the back panel of the washing machine to access the heating element. |
| 3 | Disconnect the wires from the heating element carefully. |
| 4 | Unscrew the bolt holding the heating element in place. |
| 5 | Pull out the old heating element and replace it with the new one. |
| 6 | Screw in the new heating element securely and reconnect the wires. |
| 7 | Put the back panel back on and plug the machine back in. |
| 8 | Test the washing machine to ensure the new heating element works correctly. |
Although it might seem difficult, you can change the heating element in your Beko washing machine on your own if you have the right tools and a little patience. By taking the time to carefully remove the old element and install a new one, you can prevent costly repair bills and help your machine operate more efficiently again.
When beginning the process, be sure to take all necessary safety precautions, such as unplugging the machine and turning off the water supply. You will need to take out the back panel, unplug the old heating element, and then carefully replace it with a new one. Before testing a machine, make sure everything is connected correctly by checking one last time.
Your washing machine should be able to heat water efficiently again after being replaced, resulting in cleaner, fresher clothes. To prevent any potential harm, don’t be afraid to seek professional assistance if you have any doubts at any point during the process.
