How to change the bearings and seal on an LG washing machine?

An LG washing machine’s seal and bearing replacement can increase the machine’s lifespan and save you money on expensive repairs. It might be time to take on this project if your machine has started to exhibit wear or strange noises.

With the help of this guide, you will be able to replace these important parts and restore the smooth operation of your washing machine. Regardless of your level of experience, these instructions are meant to be simple and easy to follow.

Assume you have the necessary parts and tools before beginning the process. You can quickly restore the best possible condition for your LG washing machine with a little perseverance and cautious work.

Let"s collect materials and tools

Careful planning ahead for repairs will reduce stress and save time when the work is due. In order to replace the drum bearings in an LG washing machine, an entire toolkit is required. The following inventory needs to be available:

• a pair of screwdrivers (slotted and Phillips);
• pliers;
• a hammer with a bronze striker;
• a set of open-end wrenches;
• a set of socket heads;
• a metal rod;
• WD-40 aerosol lubricant;
• silicone sealant;
• special grease for the seal and bearings.

Once you’ve determined that you have all the necessary tools, you must buy replacement parts. Make sure to specify the size of the seal and the type of bearings when choosing components, in addition to the washing machine model. The equipment’s technical passport contains the parts’ necessary specifications.

Speak with a consultant before purchasing replacement parts from a specialty retailer. Provide the washing machine’s serial number and component information. A specialist will assist you in selecting the right size oil seal and bearings.

To ensure that you don’t purchase the "wrong" part, it’s best to visit the store with the parts that need to be replaced already taken out of the washing machine body.

It is not advisable to purchase replacement parts meant for other types of machinery. In this instance, there’s a good chance the repair will need to be redone at some point after installation. About 350 rubles will be needed for the original bearings, and another 300 rubles will be needed for the sealing ring.

Once the replacement parts and tool set are ready, you should tidy up the workspace. The best course of action is to relocate the machine to the garage or, at the very least, a large room as it will not be feasible to disassemble it in a small bathroom. When performing do-it-yourself repairs in an apartment, make sure the flooring is secure by laying it down beforehand.

To ensure that nothing gets in the way of disassembling the automatic washing machine and replacing parts, it’s crucial to make as much room as possible.

Removing the tank

Disassembling the washing machine is the first step in replacing the bearings and seal. You will need to take off the machine’s front wall and top cover in order to access the tank. You will also need to take out other system components from the body. The following will be the forthcoming order of actions:

• unscrew the 2 bolts holding the top cover of the body, remove it and put it aside;
• remove the detergent dispenser. You can immediately clean it from plaque and debris;
• unscrew all the fastening mechanisms that support the control panel of the machine;
• carefully, trying not to damage or tear off the wires, put the panel on top of the washing machine;
• remove the lower false panel of the body, to do this, bend back special latches using a screwdriver;
• loosen the metal clamp encircling the cuff of the tank, remove the ring outward;
• disconnect the contacts of the hatch locking device and remove the sensor;
• Next, you need to unscrew the bolts holding the front wall of the case. You should look for screws behind the drain valve, the cuvette, on the right and left at the top of the case, on the right at the bottom and behind the dashboard. Now it will not be difficult to remove the front wall of the washing machine.

Now that access to the tank has been gained, the job is nearly finished. After that, you must unfasten the fasteners and disconnect the wiring that connects the washing machine’s tank to other components. We are discussing:

• fastening of the filling valve;
• drain pipe;
• wires leading to the heating element;
• electric motor wiring;
• cables of the pump collecting water;
• counterweight fasteners;
• pressure switch pipe;
• shock-absorbing elements.

The tank must be taken out of the case once everything that can be disconnected from it has been disconnected. You should get an assistant at this point. Pressing the springs should be done first, and then removing the component. You can manage the task on your own if you put in a lot of effort.

Tank disassembly procedure

An automatic washing machine’s tank is composed of two fixed pieces. You must loosen the special fasteners and remove all of the bolts in order to separate the halves.

If a fastener is impossible to remove, WD-40 aerosol lubricant can be used on it.

After removing the main fastening screw, you must take out the drum pulley and put the bolt back in its original position. Next, place the metal rod that has been prepared on the bolt and begin lightly tapping it with a hammer in order to knock out the shaft. Avoiding damage to the shaft is crucial, as doing repairs yourself could get expensive.

Changing damaged parts

Once the tank is divided into two sections, you can start taking out old parts and putting in new ones. The back half of the drum device will be worked on further. You will notice a sealing ring, or seal, in the center. To take it out of the seat, use a screwdriver.

The same metal rod will need to be used to knock out the bearings. After positioning the rod’s end against the bearing’s edge, hammer it in. Until the parts are gone, this process needs to be done multiple times around the whole circumference of the part.

Use a special puller to reduce the possibility of breaking the mechanism, but the cost of repairs will go up.

After the hole has been opened, all dirt, oil, and metal shavings should be removed carefully. Installing new bearings and an oil seal in a spotlessly clean environment is crucial.

It is now time to take the new parts and get them ready for installation. Don’t overlook the need to apply specific grease to the seating area. The old location is filled with the bearings. Apply a generous amount of lubricant to the oil seal in order to install it correctly. By taking this precaution, water will not get on the bearings.

Grease treatment is an additional option for the washing machine shaft. The most important thing in this situation is to remember to run the machine "idle" a few times to avoid contaminating the laundry. The washing machine and tank are subsequently assembled in the opposite order.

For more dependable structure fastening, use a moisture-resistant sealant when joining the tank’s halves. Once everything is put together, make sure the washing machine works. After connecting the device to the network, begin the "idle" washing cycle (do not fill the drum).

Although replacing the bearings and seal on an LG washing machine may seem difficult, it is absolutely achievable for a do-it-yourself enthusiast with the appropriate tools and instructions.

You can prolong the life of your washing machine and save money by taking the time to replace these parts yourself.

Just keep in mind to work cautiously, pay close attention to the directions, and make sure that all the parts are firmly in place before restarting the machine.

You can get your washing machine operating smoothly again by being patient and paying attention to details.

Although replacing the seal and bearings on an LG washing machine may seem difficult, many people can accomplish the job at home with the correct equipment and a detailed step-by-step tutorial. This guide will take you step-by-step through the entire process, saving you money on repairs and guaranteeing years of trouble-free, silent operation from your washing machine.

Video on the topic

📢 Replacing bearings and crosspieces of an LG washing machine🔥🛠️How to Replace Lg Washing Machine Bearings👍

Replacing bearings in an LG washing machine with your own hands

Replacing a bearing in an LG washing machine