It can be annoying and inconvenient when your Hansa washing machine won’t spin. You may end up with drenched clothes and an endless laundry pile as a result of this frequent problem.
Your machine may not be spinning for a number of reasons, ranging from straightforward ones like an uneven load to more complicated mechanical problems. Knowing the cause will enable you to determine whether the issue is something you can resolve on your own or if professional assistance is required.
This post will discuss the common causes of a non-spinning Hansa washing machine and offer doable solutions to restore it to functionality.
| Possible Causes | Solutions |
| Unbalanced load | Try redistributing clothes evenly inside the drum. |
| Blocked drain pump | Check and clean the drain pump filter to remove any debris. |
| Door not properly closed | Ensure the door is fully closed and latched. |
| Faulty motor or belt | Inspect the motor and belt for damage, and replace if needed. |
| Incorrect spin setting | Verify that the correct spin cycle is selected. |
Program with special settings
If you open the washing machine’s drum and discover wet laundry inside, you shouldn’t disassemble it right away to look for a problem or contact the service center right away. Maybe there isn’t even a malfunction here. Verify if spinning is involved at all in any of the special washing programs that have been activated. Generally, when any of the following washing programs are initiated on Hansa washing machines, the spin cycle is automatically stopped:
- "Wool";
- "Silk";
- "Gentle".
Consider the equipment instructions, which offer a synopsis of every washing mode. If the program that is currently running truly does not allow for spinning, simply turn on the option individually. This feature may inadvertently be disabled, even when initiating a typical wash, in which the laundry is always spun by the machine. Verify that your circumstances do not support this.
Rearrange the items in the drum
Frequently, improper distribution of items inside the drum or overloading the washing machine with laundry prevent spinning from happening. Some contemporary Hansa models come with an auto-weighing sensor; if the maximum weight that can be loaded is exceeded, these machines won’t even begin to wash. Without a specific sensor, machines can begin cleaning and rinsing the items, but even after an overload, the machinery’s functionality will be compromised:
- the washing machine will try to spin the drum, but due to the large weight of the laundry it will not be able to do this. The machine will stop working;
- the clothes will bunch up into a tight ball, the imbalance control system will be activated, the cycle will stop, the clothes will remain wet.
You must immediately remove some of the clothing from the drum and carry on washing if you think there may be an overload.
In this instance, no repairs are required. Separating the clothes into two batches and washing them separately will be sufficient. In order to prevent a tight and heavy "lump" of clothes from forming, it is crucial to straighten and evenly distribute the laundry in the drum.
Dirty water does not drain from the tank
Since the water in the tank does not entirely drain, it’s possible that the laundry in the machine is still wet after washing. This condition is typically seen when there are obstructions in the drainage system. Take the following action if you think this is the reason why the washing machine isn’t spinning out the clothes:
- de-energize the Hansa washing machine;
- cover the floor around the washing machine with dry rags;
- place a low container under the machine body, in the area of the garbage filter;
- unscrew the drain filter, collect the draining water in a basin;
- inspect the element, shine a flashlight into the hole formed after its removal. Having found a stuck object, pull it out of the machine;
- clean the debris filter and screw it back in place;
- inspect the drain hose, feel the corrugation for blockages;
- tilt the washing machine against the wall and check if the drain pipe (connecting the pump to the tank) is clogged;
- having identified a blockage, remove it;
- put all the parts back in place and check the functionality of the washing machine.
Pay attention to the way the pump operates if the filters and pipes are cleaned but the water still does not enter the sewer. It ought to hum. In the event that no sound is heard, the pump is most likely broken and will need to be replaced.
Element regulating engine speed
A tachogenerator, a unique sensor that controls engine speed, is a feature of every automatic washing machine. The motor rotor is where the element is situated.
The "brain" won’t be able to detect the drum’s rotational speed if the Hall sensor is malfunctioning, which means that the seal will either be insufficient or nonexistent.
The tachogener usually breaks down as a result of a washing machine that is consistently overloaded. For this reason, you must lay exactly the number of linens specified in the instructions inside the drum. It occurs that the Hall sensor’s fasteners weaken or its contacts break away as a result of the case’s increased vibration. In this case, you can tighten the fixers and make manual wiring corrections. There will be a solution to the issue.
You will need to remove the engine from the body in order to examine and adjust the tachogenerator. After that, you should tighten the sensor’s fasteners and inspect and clean the sensor contacts as needed. It’s possible that the sensor detached from the system. You can use a multimeter to verify this. Should the malfunction be verified, you will need to purchase and install a new tachogenerator.
All attention to the engine
One common cause of the Hansa washing machine’s inability to spin the laundry is the collector motor’s brush wear. The items stay wet in this scenario because the motor is unable to accelerate the drum to the necessary speed. You will need to disassemble the motor in order to inspect the brushes. To carry out this:
- de-energize the machine;
- remove the back wall of the housing;
- drop the drive belt from the drum pulley and the engine;
- unscrew the bolts holding the motor in the housing;
- pull out the motor.
On the sides of the collector are the electric brushes. Take out the graphite rods and examine them for wear and tear. Should the wear be considerable, the parts will need to be replaced.
Even if one electric brush is undamaged, it is crucial to replace them in pairs.
Using a multimeter to inspect the motor’s rotor and stator windings is also recommended. Upon detecting indications of a malfunction or short circuit, it will be necessary to swap out the electric motor.
It’s critical to identify the problem as soon as possible if your Hansa washing machine isn’t spinning in order to prevent more difficulties. Troubleshooting can help you resolve problems such as an unbalanced load, a clogged drain, or a malfunctioning motor.
You may be able to solve simple issues like a clogged filter or a tangled load on your own. To prevent doing more harm, it is advisable to have a professional look at the motor or control board if that is the source of the issue.
You can avoid wasting time, money, or stress by acting quickly to fix your broken washing machine. Your Hansa washing machine will function more smoothly if you perform routine maintenance and keep an eye out for any warning indications.
A clogged drain, an uneven load, or a malfunctioning motor are just a few of the common problems that could be causing your Hansa washing machine to stop spinning. Fortunately, many of these issues can be resolved at home with a few simple troubleshooting techniques.
