It takes more than just filling it up and pressing the start button to maintain the optimal performance of your Ardo washing machine. Cleaning the filter is an important but frequently neglected maintenance task. Coins, lint, and tiny objects can clog the filter over time, decreasing your machine’s efficiency and possibly leading to more significant problems.
Although it doesn’t take much effort, cleaning the filter does call for some attention. It is typically accessible because it is situated near the front of the machine at the bottom. You may keep your laundry functioning properly and prevent more serious issues by routinely inspecting and cleaning this component.
We’ll walk you through the process of cleaning the Ardo washing machine filter in this guide. We’ll go over what equipment you might need, where to look for the filter, and how to clean it properly to keep your machine running smoothly. You can keep your washing machine operating at its best and always have clean clothes with a little bit of work.
| Step | Action |
| 1 | Turn off and unplug the washing machine |
| 2 | Locate the filter at the bottom front panel |
| 3 | Place a towel or tray under the filter to catch water |
| 4 | Twist the filter cap counterclockwise to remove it |
| 5 | Clean out any debris or lint from the filter |
| 6 | Rinse the filter under running water |
| 7 | Reinsert the filter and twist clockwise to secure |
| 8 | Plug in the machine and run a test wash |
To keep your Ardo washing machine operating efficiently and extend its life, you must keep its filter clean. By routinely cleaning the filter, you can avoid clogs, which can cause unpleasant smells, subpar washing results, and even machine malfunctions. You can make sure your washer operates efficiently and gives you clean clothes and peace of mind by following a few easy steps to clean the filter.
- Cleaning the lint filter
- How to remove stubborn dirt?
- Video on the topic
- No spinning washing machine Ardo A400 solved cleaning the filter catcher repair of the washing machine 🇮🇹
- Cleaning the filter of an automatic washing machine!
- How to clean the filter in an ARDO washing machine
- How to clean the filter in an ARDO washing machine
- How to clean the filter in a washing machine
- The filter in the washing machine does not unscrew? The drain filter in the washing machine does not open?
Cleaning the lint filter
The drain and inlet filters are found on Ardo washing machines. The first one removes the majority of the rust, sand, and limescale from the water entering the machine. By filtering the waste liquid, the second method keeps deposits and debris out of the sewer hose and pump.
The drainage system would malfunction continuously without a drain filter because the hose would become clogged with hairs and lint and the pump would become dirty and eventually fail. With it, the majority of the trash that enters the machine is held in check on the plastic spiral nozzle that is situated at the drum’s exit. Cleaning the garbage filter is not difficult, and you can do it on your own without hiring a repairman. All you have to do is get ready and adhere to the guidelines. It also won’t harm to have a cursory understanding of the Ardo’s internal workings.
Exercise caution! The machine will release water when the filter is unscrewed!
You must first ascertain the location of the "garbage can." It’s easy to find; in the majority of washing machines, it’s on the front panel, bottom left. You must unhook the technical hatch door from the body in order to remove the filter. We take the following actions in order:
- disconnect the washing machine from communications;
- we move the machine to the center of the room;
- tilt the body back, raising the front a few cm;
- use a flat screwdriver to pry up the false panel and press the latches;
- place a container under the drain filter (even after draining, there is still water in the tank, which will spill out onto the floor when the filter is unscrewed);
- if there is an emergency drain hose, activate it;
- unscrew the filter plug;
- remove the nozzle from the seat.
Cleaning the filter is the next step. The nozzle is fully cleaned after removing any large debris. It’s crucial to use only warm water because boiling water deforms plastic and sealing rubber. Next, keep an eye on the filter seat. Debris also makes it extremely dirty, so you should clean it with a sponge dipped in soap. Then locate the pump impeller by shining a flashlight through the drainage system. You will need to clear any hair, dirt, or other debris obstructing it from the blades if it rotates tightly.
Once the nozzle has been cleaned, replace it firmly and move on to the next step of checking: connect the machine, begin rinsing, and pay close attention to the "trash can." If there isn’t a leak, the cleaning was effective. The washing machine needs to be moved back against the wall and the false panel needs to be put back on the Ardo.
How to remove stubborn dirt?
You’ll need more powerful products to remove the trash filter if it hasn’t been cleaned in a while; regular water won’t be sufficient. In this instance, start with "deep" cleaning after surface cleaning. You’ll have to soak, use a brush to rub, or hire professionals to clean.
- Cleaning with a toothbrush. Small but caustic plaque is removed with an old toothbrush and laundry soap. Rub as hard as possible.
- Soaking. Heavy dirt needs to be "soaked". Dilute soda and citric acid in warm water in a proportion of 20-50 g per liter, lower the filter into the solution and leave for 30-120 minutes. Afterwards, wash off the remaining rust and scale under the tap.
- Processing with special agents. It is easy to find strong household chemicals in stores to remove rust and scale. You just need to follow the instructions on the packaging.
The rubber and plastic used in Ardo filters resist chemicals and friction quite well. The most important thing is to keep boiling water and strong alkalis off the nozzle because they cause the materials to distort.
To keep your Ardo washing machine operating efficiently and prolonging its life, it’s important to keep the filter clean. Maintaining a clean filter helps to keep your machine operating efficiently by averting potential problems like leaks and blockages. It also keeps your laundry smelling fresh and helps prevent offensive odors.
First, unplug the machine and turn it off to ensure safety before beginning to clean the filter. Find the filter, which is typically located near the machine’s front bottom, and carefully take it out. Clear away any debris, coins, or lint that might have accumulated. After giving the filter a quick rinse under water to get rid of any last bits of residue, firmly put it back in its place.
You can avoid future major repairs by performing this easy maintenance task every few months. It’s a quick fix that will pay off big time by keeping your Ardo washing machine operating at peak performance and simplifying your laundry days.
