When a washing machine doesn’t operate as intended, it can be particularly annoying when the water fills up first and then immediately drains. You might find yourself scratching your head over this problem, unsure of what’s wrong and how to fix it. Restoring the functionality of your machine requires an understanding of the potential causes of this malfunction.
There are a few possible reasons why your Candy washing machine is filling and emptying at the same time. It might be as straightforward as a kinked drain hose or as complicated as an internal machine component issue. Being aware of where to search and what to check can help you avoid wasting time or having to pay for an expensive repair service.
In this post, we’ll examine the most typical causes of this problem and offer some helpful advice on how to diagnose and resolve it. Whether you’re a do-it-yourself enthusiast or just want to know what’s wrong, these tips will give you the confidence you need to solve the issue.
| Possible Cause | Solution |
| Faulty water level sensor | Replace or repair the sensor to ensure proper water level detection. |
| Blocked drain hose | Check and clean the drain hose to remove any blockages. |
| Defective drain pump | Inspect the drain pump and replace it if it"s malfunctioning. |
| Incorrect installation | Ensure the drain hose is installed correctly and at the right height. |
A broken pressure switch or an issue with the location of the drain hose are probably the causes of your annoying Candy washing machine filling up with water and then quickly emptying it. These parts may inadvertently cause the machine to stop the wash cycle as soon as water is added by signaling to drain. Recognizing and resolving these issues will help you get your machine back up and running smoothly while avoiding needless water waste.
- The nature of this malfunction
- Incorrect location of the hose
- Self-draining is caused by a blockage
- Video on the topic
- Fills with water and immediately drains? Long washing time? How to fix
- Candy washing machine fills and drains water. Error E22. Diagnostics. Repair
- Washing machine fills and immediately drains water.Self-draining | Podkluchaem.by|Specremont.by
- Repair of the Lg washing machine always drains water..Lg module repair.
The nature of this malfunction
It is easy to spot when a Candy washing machine fills up with water but quickly empties the drum. First of all, the cycle—which never ends at the scheduled time—can be used to monitor this. Additionally, the machine continuously emits the sound of a running sewer. The fact that the laundry left in the "home assistant" is still unclean is possibly the most unsettling indicator. This circumstance may arise due to:
- improper installation of the drain hose;
- clogged sewer;
- malfunction of the valve;
- malfunction in the pressure switch;
- failed control board.
It is interesting to note that if there is an issue with the water intake, contemporary Candy models will immediately shut off the cycle and display an error!
Such a malfunction should be fixed as soon as possible, as unchecked drainage can seriously harm every component of the system. This raises the possibility of pipes, valves, and pumps failing. In addition, there’s a chance that the apartment will flood, leak, or experience a short circuit.
Incorrect location of the hose
Make careful to inspect the state of the drain hose if you have recently moved or installed the washing machine. This element is frequently installed improperly, which results in issues with water intake and drainage. There are two methods to find out if everything is in its proper place.
First, give the corrugation a close inspection. The unit’s tank is about 50–60 cm above the floor, so it should be fixed slightly above that level, per the instructions. This balance causes the "siphon effect," which prevents the liquid from exiting the drum on its own. Water will start to be forced into the sewer if the harmony is broken, and the pressure switch will respond by starting up again. Until someone steps in or the power is turned off, this cycle will keep going.
If accessing the "sleeve" is challenging, there are alternative methods you can use to ensure the installation is correct. You should start a quick wash and assess the machine’s behavior in order to do this. If water starts to flow out of it right away, the hose needs to be adjusted.
It is very easy to solve the issue of the corrugation being positioned incorrectly. All you have to do is locate a special plastic loop that comes with every machine in the brand, and adjust the hose level in accordance with the guidelines provided. After that, we insert the "hook" into the appropriate location and thread the rubber through it.
Self-draining is caused by a blockage
Blockages can also cause problems for the drainage system. For instance, if there is dirt buildup in the pump, on the impeller, or in the pipes, the pump will operate erratically and the water in the tank may unintentionally drain. You must clean the Candy washing machine’s trash filter as well as the other filter components in order to resolve this issue. To accomplish this, you must:
- disconnect the unit from utilities;
- find the technical hatch in the lower right part of the case, pry it up and remove it;
- grasp the protruding part of the trash filter (located on the right edge) and unscrew it by turning it counterclockwise;
- clean the spiral under water.
Armed with a flashlight, you can shine through the freed hole and check how dirty the snails, pipes and impellers are. If the trash filter is covered with a thick layer of scale, soak it in a warm solution of citric acid and wait 30-40 minutes. If you still can’t open the hatch, try checking the drain in another way. You will need to disconnect the equipment from all utilities and move it to the middle of the room. Then you need to carefully turn the "home assistant" on its right side and look into it through the bottom. Candy washing machines, as a rule, do not have a bottom, and this greatly simplifies the diagnostic process.
It can be annoying to deal with a washing machine that fills up with water and then quickly drains, but troubleshooting can be made much simpler by knowing the potential causes. A malfunctioning drain system, such as a clogged or incorrectly installed drain hose, is frequently the cause of this problem. A quick fix for the issue is to make sure the hose is at the proper height and clear of any obstacles.
In rare circumstances, the issue could be the result of a broken pressure switch or an issue with the control board of the device. These parts are essential for controlling the water level; if they break, the washing machine may think it has to empty the water right away. To identify the problem, check these parts and refer to the manufacturer’s instructions.
If, in spite of your efforts, the issue still exists, it might be time to contact a qualified technician. It’s critical to take quick action to fix the problem in order to save more damage to the washing machine and guarantee optimal performance. You’ll be more prepared to fix this issue and restore your machine to normal operation if you know the typical causes of it.
