Beko washing machine does not spin

It can be confusing and frustrating if your Beko washing machine stops spinning all of a sudden. Clothes left in a washing machine that doesn’t spin properly end up drenched and take longer to dry. But don’t worry, there are a few typical causes for this to occur, and many of them can be resolved without the assistance of a specialist.

Various factors can lead to a Beko washing machine not spinning, such as problems with drainage or the door latch or load size. You may be able to diagnose and possibly fix the problem on your own if you are aware of these potential causes.

We’ll go over some of the most typical causes of your Beko washing machine not spinning in this article, along with what you can do to fix it.

List of possible problems

Do not put up with wet laundry. Not only is it tedious and time-consuming to complete the selfless task of washing a machine, but an unrepaired malfunction can worsen the situation to the point of catastrophic consequences. You must comprehend the variety of potential causes for the failed spin in order to determine where to search for a malfunction. Regarding Beko models, the following scenarios come to mind:

• a program without spin is selected;
• the drum is unbalanced;
• the drain does not function;
• the tachogenerator is out of order;
• the electric motor is broken;
• the drum bearings are worn out;
• the control board is not working;
• a foreign body has gotten into the tank, preventing the drum from spinning.

The problem can be resolved on its own in 99 percent of cases. A professional repairman’s assistance will only be required in the event that the control module burns out. It is sufficient to continuously explore every potential solution in order to accurately identify the malfunction’s source. Detailed instructions are provided below.

Let"s check the washing program

First, it’s advisable to eliminate circumstances that don’t involve accidents. Since the user inadvertently selects a mode that does not require intense drum rotation, there is frequently no breakdown. For instance, spinning is not offered for programs involving wool, silk, and down as well as for delicate washing.

You must read the manufacturer’s instructions and keep in mind the button you have selected in order to validate your suspicions. The next time, simply switch to a different mode or activate the spin cycle in addition. Second, see if the spin was inadvertently canceled in the default program.

Crucial! The control panel lock will help you avoid worrying about inadvertent switching, so don’t ignore it.

You can adjust the drum’s rotational speed on many contemporary models all the way up to zero. It is preferable to run a test: choose a mode, increase the spin speed, and restart the device. Items that are wet will warrant additional examination.

Let"s look at the laundry in the drum

A Beko washing machine’s spin function frequently malfunctions because of a drum imbalance. Unbalance is caused by overload, inadequate loading, or uneven laundry distribution on the tank walls. Older models have this issue because more recent models have a unique feature that regulates the balance while the machine is spinning and washing.

Given that the unit in question keeps attempting to spin up but is unable to do so, it is simple to suspect something is amiss. Consequently, the laundry stays wet and the cycle ends 7–15 minutes earlier than scheduled. Here’s how you can make things right:

1. Wait for the hatch to unlock and open the door.
2. Take out half of the laundry (if overloading was allowed), untangle the twisted "lump" or add more things (if there is a shortage).
3. Close the hatch tightly.
4. Start the spin.
5. Check the laundry for dryness.

Avoiding imbalance is preferable because it negatively impacts the shaft, bearing assembly, and shock absorbers. It’s critical to keep both the upper and lower limits in mind when loading the laundry. Therefore, you must wash at least 1 kg in a machine with a capacity of up to 5 kg and 2.5 kg in washing machines with a maximum capacity of 8–9 kg.

Waste water is not removed

You should check the drainage system if, at the end of the cycle, the drum contains both wet materials and a full water tank. It’s possible that a burned-out pump, a clogged pump impeller, or a blockage in the hoses or pipes is the reason the machine is unable to empty the waste liquid. The following is the order in which we search for a particular cause and its resolution:

1. Disconnect the drain hose from the sewer and probe it along its length for blockages. If foreign objects are detected, we unscrew the pipe completely and wash it under strong water pressure.

Take note! When the general sewer becomes clogged, we insert the disconnected drain hose end into the bathtub or sink, turn on the drain or spin mode, and watch for water to start flowing.

1. Find the drain hatch in the lower right corner of the washing machine body and, prying it with a screwdriver, open it. Place a container to collect water and unscrew the garbage filter Clean the part and the pipes suitable for it. If everything is clean, ring the contacts with a multimeter.
2. Check the integrity of the pump. Free the impeller from wound hair and wool, clean the pump body and measure the value of the existing resistance.

In the event of a breakdown, new parts are substituted for the pump and filter, which are irreparable. Once all the adjustments have been made, turn on the machine for the quickest wash and keep an eye on the water drain. A drum that is empty will rule out a drainage system malfunction.

The Hall sensor does not function

The tachogenerator is malfunctioning and the spin is not functional. This device, also known as the Hall sensor, is in charge of keeping track of the engine’s revolutions and sending data to the control board. In the event of a malfunction or loss of communication with the module, the system ceases to receive data and lowers the motor power for security.

The machine was not used properly, which is what caused the breakdown, specifically:

• Regular overloading of the machine with laundry.
• Prolonged use of the machine without stopping.
• Loose fasteners.
• Loose contacts or damaged wiring.
• A strong voltage surge or short circuit.

We start by looking over the cables and tightening the terminals if needed. We then clean and insulate the conductors. Next, we use a multimeter to measure the sensor directly and assess the outcome. We substitute an analog for any deviations from the average.

The motor does not spin the drum

When the engine cannot accelerate to the necessary power, another scenario arises. When electric brushes in collector motors wear out, spinning stops being possible but washing and rinsing continue to be normal. If passing other phases of the cycle proved challenging, there’s a chance that the engine is malfunctioning. The following method is used to verify the guess:

1. Disconnect the machine from all communications.
2. Unscrew the back cover.
3. Remove the drive belt.
4. Disconnect all connected places.
5. Loosen the retaining fasteners.
6. Swing the motor and take it out of the grooves.

After that, use a cloth to wipe the body and look for any damage. A burnt-out engine has charred wires, stains, and an unpleasant burning smell. Next, take note of the electric brushes. Take them out of the engine on both sides, open them, and gauge the length of the tip. You will need to get a new pair if the difference is less than 0.7 mm. Ring the coils simultaneously.

Failure of the electronic unit

The worst case scenario is an electronics malfunction. In this instance, the spin-causing triac burns out, the engine is unable to accelerate the drum and does not receive an acceleration command. If you have the slightest suspicion, you should get in touch with the service department because only a specialist can determine why the problem is in the module.

Doing the module’s repair yourself is not advised. The likelihood of a final board breakdown due to insufficient experience, tools, and professionalism is very high. It is less expensive to hire a specialist than to purchase a replacement part.

A foreign object in the tank

Additionally, the drum cannot spin due to an object lodged in the tank. In this situation, you must act quickly because an external object may harm the container walls and cause the system to become completely jammed. Because replacing the tank would be very costly, it is advised to stop the machine and remove the potentially dangerous component as soon as there is any suspicion.

It is best to get the diagnosis confirmed first because the object is difficult to remove. Turn off the machine from the network, open the hatch door, empty the water, and rotate the drum in both directions to accomplish this. It is evident from the resistance that there is a barrier in place, so let’s get started:

1. We check the disconnection of the unit from the power supply.
2. Turn off the water and disconnect the drain hose.
3. Ensure free access to the machine from all sides.
4. Unscrew the bolts at the back and remove the back wall.

Crucial! Prior to using your BEKO model, find out which side the heating element is on by consulting the instructions.

1. Find the location of the heating element.
2. Take a photo of the heater so as not to mix up the wires when returning.
3. Loosen the retaining bolts and take out the heating element.
4. Put your fingers or long pliers into the vacated space and pull out the object that fell into the tank.

It is worthwhile to clean the heating element on an as-needed basis once the machine is operating normally again. Make sure to clean the contacts and remove any scale or dirt from the surface by scraping it off. After that, put everything back where it belongs and check the drum’s rotation.

It can be annoying if your Beko washing machine won’t spin, but there are a few common problems you can check and resolve on your own. Simple issues like an uneven load, an incorrect spin setting, or a clogged drain are frequently easily fixed.

After examining these, if the machine still won’t spin, there may be a more serious problem, such as a broken control board or motor. It’s advisable to get in touch with an expert in these situations to prevent more harm.

You may save time and prevent needless stress by being aware of the possible causes and knowing when to get assistance. Maintaining a well-maintained washing machine guarantees a hassle-free and seamless laundry routine.

Some common problems that could be causing your Beko washing machine to stop spinning include an uneven load, a clogged filter, or a broken door latch. Knowing these typical issues will enable you to troubleshoot issues quickly and possibly resolve them without the need for expert assistance.

Video on the topic

How to reset an error on a Beko washing machine

How to properly reset a BEKO washing machine