Beko washing machine does not spin the drum

It can be very annoying if your Beko washing machine isn’t spinning. To ensure that your clothes are dry and ready to wear, use the spin cycle. If it fails, you may be left with a ton of stress from doing laundry and soggy clothes. But don’t worry, there are usually solutions for this issue, which usually boil down to a few common issues.

There are a few possible causes for improper spinning in your washing machine. It might be as easy as an uneven load or a small problem with the door lock. Alternatively, it could be a more complicated issue such as a pump issue or a broken motor. You can solve the issue more successfully if you are aware of these possible problems.

In this piece, we’ll go over some of the most typical causes of your Beko washing machine not spinning and offer helpful solutions. We can help you whether you’re a do-it-yourself enthusiast or just need a quick fix. Let’s get started and restore your washing machine to its peak performance!

Why the drum stopped?

You must examine the washing machine’s operation prior to its cessation and conduct an equipment diagnosis in order to determine why the drum stopped spinning. It is essential to identify the malfunction’s cause and take action to fix it. The primary tank typically "freezes" in situ because of:

• problems with the drive belt or drum "wheel" (the reason may be in the rubber band and in the pulley);
• foreign object that got inside the tank. He stuck between its walls and the drum and blocks the rotation of the latter;
• failure of the coil of the engine;
• Strong wear of engine electric shock. Coal rods are erased and cannot fully fulfill their functions;
• damage to the semiconductor elements of the main control module;
• Washing the lamella of the motor.

The list of potential explanations for why the washing machine might not twist the drum is far from exhaustive. The simplest washer is made up of numerous parts, connections, diagrams, and individual elements, any one of which can cause a stopping stop.

Independent diagnostics for the Beko machine should begin with the most basic diagnosis and proceed to eliminate each cause in turn. If you run into trouble verifying individual nodes, you can get expert assistance.

It can be annoying and perplexing if the drum on your Beko washing machine isn’t spinning. Usually, there are a few common issues that lead to this problem, like unbalanced loads, problems with the drive belt, or even a broken motor. You can troubleshoot the issue more successfully and decide whether you can solve it on your own or if you need professional assistance by being aware of these potential causes.

Transmanding mechanism

Which steps should I do first? The drive belt is usually the cause of the machine Beko’s drum stopping its rotation. It’s possible that the rubber band broke or detached. If this is a one-time "promotion," all that will be required is the purchase of a new element, the removal of the washing machine’s back panel, and its installation on the engine pulley and drum.

You will need to "dig" deeper to rule out a pulley break if the drive belt continues to come off frequently even after replacement.

A fresh rubber band that comes off the "wheel" once more even after multiple washings indicates a major issue. In order to verify the version regarding the drum pulley damage, you need to:

• de-energize the washing equipment;
• close the shut-off valve responsible for the water supply;
• pull out the washing machine to gain access to its rear part;
• remove the service hatch or the back panel (depending on the Beko machine model);
• inspect the drum pulley (it is a large wheel). If it is in perfect condition, you can pull the drive belt back into place. If there are any defects or deflections on the surface, the circle will have to be changed;
• look at the pulley mounted on the motor shaft. If the circle is deformed or damaged, be sure to reinstall the wheel.

It is best not to wait too long to replace the pulley if you notice any wear, cracks, bends, or other defects. Reinstalling a drum wheel is actually very easy; even a novice can perform it. To replace the damaged element, simply purchase an identical circle, unscrew the locking bolt, and remove it. Let’s take a closer look at the forthcoming action algorithm.

1. Using a wooden block, block the movement of the drum "wheel". If the circle is deformed, then there is no need to protect it. It is important to preserve the screw and thread in the process, so you should act carefully.
2. Treat the central bolt with WD-40 aerosol lubricant. Wait half an hour for the substance to take effect.
3. Take a wrench of the appropriate size, carefully unscrew the screw. In this case, you do not need to press too hard on the structure so as not to damage the bolt and thread.
4. Remove the old "wheel".
5. Put a new pulley on the shaft, fix it with a fastener bolt.

It is advised by experts to replace the drive belt and drum at the same time.

The process of changing the wheel is not difficult at all. It is crucial to avoid going overboard in order to avoid breaking the thread. After the Beko machine has been repaired, start a test wash and see how freely the drum rotates with your hand.

Foreign body in the tank

The risk that outsiders of solid objects that have fallen into the tank are provoked is a warning that equipment repair specialists constantly reiterate. Tell how much the repairs in this case might end up costing. Despite this, people frequently disregard the advice to wash bras in specific bags and fail to check the pockets before packing items into the drum. Coins, paper clips, nails, pins, buttons, bodice bones, and so on become lodged between the drum and the tank.

If the items were quietly resting on the tank’s bottom, the trouble would be cut in half. They may, however, occasionally cause the drum to jam and harm the plastic tank. This is an expensive repair since you will need to replace the entire unit.

Start the washing cycle instead of trying to manually unscrew the drum if it is jammed for this reason. As soon as possible, the stuck object needs to be taken out of the washing machine tank. The heating element or drain pipe hole can be used for this.

This is the better way to access the stuck little item if the heating element on your Beko model is situated in the back of the case. The machine’s service hatch must be removed, the heating element’s power supply must be disconnected, the fastening nut must be loosened, and the heater must be removed. The object obstructing the drum’s rotation can be effortlessly removed from the tank thanks to the resulting hole.

It’s best to forget about trying to fit something foreign through the heating element’s opening when it’s in front. This will require removing the case’s front panel, which is a challenging task. Attempting to remove the stuck small items in this manner is much easier:

• drain the water from the system through the trash filter;
• lay the machine on its side;
• loosen the clamp securing the drain pipe, disconnect the hose from the tank;
• remove the foreign object through the drain hole.

Check the movement of the drum after the issue has been resolved. You can assemble the Beko machine and carry on using the equipment if it spins freely.

It could also be the motor

You will need to inspect the engine if diagnostics reveal that the drive belt, pulley, or foreign object is not the cause of the drum stopping. Examining the motor’s electric brushes and coil should be your first step. The following will be the sequence of events:

• disconnect the machine from the network, close the shut-off valve;
• disconnect the drain and inlet hose from the body;
• lay the washing machine on its left side;
• take a photo of the wiring diagram to the motor, then disconnect the contacts;
• unscrew the bolts securing the motor;
• remove the unit from the housing;
• use a multimeter to check the resistance of the motor coil. If you find that the part has burned out, you will have to replace it;
• pull out the brushes located on the sides of the motor. If even one of them is badly worn out, you need to change the pair.

If the brushes and coil are in good working order, a broken motor wire or damage to the lamellas could be the cause of the obstruction in the drum movement. By connecting the motor directly, you can determine if it is indeed defective. Should the worst turn out to be true, the motor will need to be changed. Repairing it is not feasible because it is unclear if rewinding or boring the lamellas will produce any benefit.

It can be annoying if your Beko washing machine won’t spin, but there are a few things you can try to fix the problem. To start the spin cycle, first ensure that the load inside the drum is not excessively heavy or unbalanced. Redistributing the clothing or lightening the load can occasionally fix the issue.

A door lock issue could be another frequent concern. If the door is not securely fastened, the machine will not rotate. Verify that nothing is blocking the door latch and that it is operating properly. Should the latch be broken or malfunctioning, it may need to be replaced.

Check the drainage system as well. The reason behind your washing machine not spinning could be a blocked or clogged drain hose. Verify that the hose is not bent or kinked and that there are no impediments in its path. As the filter occasionally becomes clogged with debris or lint, cleaning it may also be helpful.

It might be time to get help from a professional if you’ve tried these solutions and the issue still exists. There might be a problem requiring professional attention with the motor or other internal components. Your washing machine’s lifespan can be increased and smooth operation can be ensured with routine maintenance and fast repairs.

Video on the topic

BEKO WM 74135W washing machine drum does not spin

A common malfunction of the BEKO washing machine is the wear of the brushes

Beko washing machine drum not spinning

BEKO washing machine does not spin the drum. Why the machine does not spin the drum

Beko WKB 41001 washing machine does not spin the drum.

Beko washing machine does not spin the drum (inverter)