It can be very annoying if your Beko washing machine is not draining water. Your laundry routine may be disturbed by this problem, leaving you to wonder what went wrong. Recognizing the typical causes of this issue will enable you to find a fast and efficient solution.
Your washing machine may not be draining properly for a number of reasons. It might be the result of a blocked pump filter, a clogged drain hose, or even a broken pump. You can frequently identify the source of the issue and take the required action to resolve it by looking at these components.
We’ll go into great detail about these typical problems in this post and offer workable fixes to help you get your Beko washing machine back up and running. Our advice will help you navigate the troubleshooting process, regardless of the complexity of the problem you’re facing.
| Possible Issue | Solution |
| Clogged Drain Filter | Check and clean the drain filter. It"s usually located at the bottom front of the machine. |
| Kinked Drain Hose | Inspect the drain hose for any kinks or bends and straighten it if necessary. |
| Blocked Pump | Check if the pump is blocked with debris. You may need to remove any obstructions. |
| Faulty Drain Pump | If the pump is not working, it might need to be repaired or replaced. |
| Incorrect Washing Program | Ensure you have selected the correct washing program that includes a draining cycle. |
A clogged drainage hose, a broken pump, or a blocked filter are just a few possible causes for your Beko washing machine not to be draining water. To resolve these issues, make sure the hose is clear of obstructions, check and clean the filter, and look for blockages in the pump. You can frequently fix the problem and restore your washing machine’s functionality by following these steps.
Filter element
You will need to examine the washing machine’s behavior in order to determine what caused the drainage failure. It’s critical to know the precise moment the system "hung up," the volume of water that was "pumped out" of the tank, and the machine’s noise level prior to the incident. Determining the cause and the appropriate course of action requires first diagnosing the equipment.
Generally speaking, there are two reasons why Beko drainage issues arise: clogged garbage filters and pump malfunctions. It is best to start checking with the "garbage can" in any case. We behave as follows:
- de-energize the machine;
- disconnect from the water supply;
- remove all objects that do not tolerate moisture (powder, rugs) from the machine;
- protect the area around the machine from water by covering everything with oilcloth, rags or newspapers;
- prepare a container to collect water;
- pry up the door of the technical hatch located in the lower right part of the body with a flat screwdriver and remove it;
- find the garbage filter – a black round cover;
- tilt the washing machine back until the front legs are 3-8 cm off the floor;
- place the container under the filter.
After getting ready, take the filter off. It’s easy to unscrew the filter; just grab the part that protrudes and rotate it clockwise. Pull the spiral in your direction to take it out of the seat as soon as it becomes less tight. Water will start to splash out of the tank as soon as everything is done as carefully as possible.
It is important to thoroughly inspect and clean the removed filter. First, tidy out tangled hair, dense dirt, and stuck debris. The spiral is then thoroughly cleaned with warm running water. You will need to soak the area if the "garbage can" has deposits and scale on its surface. Soak the plastic in a solution of diluted citric acid and warm water for 5-8 hours. It is not possible to use boiling water because the material easily deforms at high temperatures.
There will be burns if you try to remove the garbage filter while the water in the drum is still hot.
An unclean filter seat could be another cause of slow drainage. Consequently, it is advised to use a flashlight to illuminate the opened hole and remove any foreign objects after unscrewing the "garbage can." Additionally, it’s a good idea to "go" over the interior surfaces with a damp cloth. You will need to investigate the washing machine pump further if the issue persists after cleaning.
Dismantling the pump
The pump is frequently to blame for the challenging drain. In order for the washing machine to empty the drum when it stops, this is what should pump out dirty water from the tank. It is vital to diagnose and fix the pump in order to remedy the issue. However, you must first take it out of the machine gun.
To reach the pump through the bottom in the laundry rooms. A wrench, screwdrivers, and a container for collecting water must be ready. After that, the machine must be disconnected from the communications network and disassembled. We operate in accordance with the following plan.
- We push the technical hatch with a flat screwdriver and click it.
- We twist the garbage filter.
- We free the pump from the holding bolt.
- Wean all the summarized wires and nozzles.
- Turn the pump counterclockwise, while pushing the pump deep into the pump.
- We put your hand through the bottom and pull out the pump.
- Put the part on a dry surface and begin to search for a malfunction.
Disconnecting the washing machine from communications is a must before disassembling!
Reaching the pump with your hands was more convenient, and you could return to the left side. This will expedite the pump’s disassembly because you won’t need to operate by touch. After disconnecting the pump, we begin the diagnostic process.
Let"s disassemble the part and take a look
Cleaning the drain pump is necessary before repair. More specifically, the pump’s impeller needs to be cleaned. You must take out the rotating component in order to do this. It’s easy to do this: take out all the screws on the body with a screwdriver, then cut the body in half to locate the bladed "head."
Revolving the impeller is necessary, but not too much. A tighter fit is required for the component if the "wheel" detaches from the landing axis. We behave differently when the blades are blocked; we remove any hair, threads, and debris that may be causing interference. The snail and pump are cleaned simultaneously.
The washing machine should be thoroughly cleaned at least once a year, according to the manufacturer’s recommendations.
The parts that have been cleaned and rearranged are the pump’s impeller and the snail’s impeller. The installation procedure is carried out in the opposite order. It is advised to perform a test wash and assess the caliber of the work after it is finished. The issue has been resolved if the cycle operates quietly, the water successfully empties from the drum into the sewer, and the self-diagnostic system does not register a failure. If not, you’ll need to find a substitute.
It’s critical to solve the problem as soon as possible if the water in your Beko washing machine isn’t draining correctly to prevent more difficulties. A clogged filter, a blocked drain hose, or issues with the pump are typical causes. To determine whether they require cleaning or repair, start by inspecting these parts.
There are situations when the problem could be more complicated, like when the control board or pump aren’t working properly. It’s best to refer to the user manual or get in touch with a qualified technician in such circumstances. Frequent maintenance can also aid in preventing the recurrence of these problems later on.
You can usually fix the draining problem and get your washing machine operating again by following these steps. To protect your safety, always remember to turn off and unplug the machine before attempting any repairs or inspections.
