You’re probably annoyed if your Ariston washing machine fills up with water and then quickly drains it. This issue has the potential to disrupt your washing schedule and leave you perplexed as to why.
Although this problem initially appears to be complex, it’s usually the result of something quite straightforward. Knowing the potential causes will help you decide what to do next and whether you need professional assistance or can fix it yourself.
This post will examine the typical causes of this issue and offer advice on how to resolve it. You can quickly get your washing machine operating correctly again if you take the appropriate steps.
- What could have happened?
- We test the heating element with our own hands
- Video on the topic
- Ariston AVSL 1090 washing machine constantly drains water
- Hotpoint Ariston LSF 7237 X The machine collects water and immediately drains it
- The washing machine does not wash, immediately drains water into the sewer: solution to the problem
- The washing machine collects and drains water at the same time. Simple solution to the problem!
- The washing machine constantly collects water. How to solve the problem. Ariston Hotpoint RST 703 D
- Indesit washing machine is glitching, collects and drains water! DIY repair!
- The washing machine collects and drains water! Constantly pumps out water!
What could have happened?
The washing machine’s ability to fill with water and quickly empty it is highly noticeable. First of all, the machine stops at this point in the washing cycle. Second, there will be a continuous gurgling noise as liquid flows into the pipe. A malfunction of this kind may be caused by:
- an incorrectly positioned drain hose;
- an incorrectly functioning pressure switch;
- a broken heating element;
- a damaged drain valve;
- a failed control module.
In the event that the drain hose is connected below the necessary level, gravity will remove the water from the tank. As a result, it’s crucial to place the hose under the designated bend, just like the instructions say. The distance between the outlet point and the floor should be between 60 and 80 cm.
The "brain" will receive inaccurate information from a malfunctioning level sensor. Thus, the pressure switch will detect an overflow and initiate the drain when the tank is empty. Water will thus be gathered and sent straight into the sewer.
Every procedure is managed by the electronic unit. In the event that the control module malfunctions, the washing machine may begin to operate improperly, collect water, and then quickly drain it. In this scenario, a thorough board diagnostic will be necessary.
Statistics show that improperly connected drain hoses or malfunctioning heating elements are the main causes of endless water filling and draining on Aristons.
If the machine is not washing, we will advise you on what to do. Now let’s see where to begin diagnosing a washing machine made by Ariston. The issue of the water constantly filling and emptying needs to be resolved right away; don’t put it off.
If water fills your Ariston washing machine and it empties it right away, there’s probably a problem with the drain system or a broken sensor. It’s critical to look for obstructions or flaws in the drain hose, pump, and water level sensor because this issue can waste water and prevent washing. Your machine’s normal functioning can be restored by resolving these problems.
We test the heating element with our own hands
Rule out a drain hose issue once the machine gathers and quickly empties water. The liquid will start to drain naturally if the drain hose is not attached properly. The procedure will carry on indefinitely until the pressure switch signals to fill the tank once more.
The Ariston washing machine’s instructions include recommendations for connecting the drain hose. It ought to be between 60 and 80 centimeters above the ground. Furthermore, the sleeve is beneath a specific bend.
Strange as it may sound, an uncontrolled water intake and drainage can result from a broken heating element on Ariston washing machines. Frequently, the heater is the root of the issue. You’ll need a multimeter, which is a specialized tool, to check the tubular element. The following will be the sequence of events:
- de-energize the machine;
- unscrew the screws holding the back panel of the washing machine, move the wall aside;
- find the heating element – it is located in the lower corner;
- remove the wiring from the heater;
- set the multimeter to resistance measurement mode, setting the selector to the 200 Ohm position;
- attach the multimeter probes to the contacts of the heating element;
- measure the resistance.
Snap a picture of the wiring schematic connecting the heating element contacts to avoid mistakes during reassembly.
The readings should typically fall between 20 and 60 ohms. The heating element is then inspected for any problems. Setting the multimeter’s maximum allowable resistance value (in megaohms) is necessary in order to accomplish this. Next, one tester probe needs to be placed on the body of the heating element, and the other one needs to be brought to each component contact one at a time.
The multimeter screen will show a number other than one when a breakdown happens. Once a malfunction has been identified, the heating element needs to be replaced. Repairing the heating element is not possible.
Try turning on the machine after turning off the heater if multimeter measurements show that the element is fully operational but the machine still does not wash. Without a heating element, the majority of Ariston models operate in silence. In this instance, maybe the "home assistant" will fill up fast and the drum will start to rotate.
You will need to replace the tubular element if the machine begins to wash without a heating element. When purchasing parts, consider the power of the previous heater and the model of the Ariston washing machine. You don’t need an expert’s assistance to replace it.
| Problem | Possible Cause |
| Washing machine fills and drains immediately | Drain hose positioned too low, creating a siphoning effect |
| Water never stays in the drum | Incorrect installation of the drain hose |
| Machine doesn"t start washing cycle | Faulty water level sensor |
It’s probably time to fix the problem if your Ariston washing machine is filling up with water and then quickly emptying it. A few typical causes, like a broken water level sensor, a clogged drain hose, or a problem with the machine’s control board, are frequently responsible for this issue.
A thorough inspection of these parts to make sure they’re in good working order usually fixes the problem. To prevent more harm, it might be necessary to speak with a qualified technician if the issue continues.
By performing routine maintenance, you can keep your washing machine in good working order and avoid future problems that could cost you money and effort.
